synth_tools

Back

-0.956711 0.0765948 0.280779 facet normal -0.782844 -0.468318 0.409675 vertex 5.77934 4.34766 7.60514 vertex -5.81619 4.41238 7.55007 facet normal -0.195093 -0.980785 -7.41558e-06 vertex 0.4 -2.9093 18.8747 vertex 1.2151 -2.93351 18.7502 vertex 2.9008 0 18.9335 facet normal -2.766623e-01 2.569074e-03 9.609638e-01 facet normal 9.807580e-01 -1.766960e-03 -1.952194e-01 vertex -9.049876e+01 1.005513e+02 1.168708e+01 facet normal 0.0723002 0.0677156 0.995082 vertex -5.16066 -6.47125 19.9688 facet normal -0.290271 0.956871 -0.01189 facet normal -0.575169 -0.528289 0.624573 facet normal -9.428339e-01 3.440546e-03 -3.332453e-01 vertex -1.070034e+02 9.665134e+01 4.645269e+00 vertex -1.070749e+02 9.665134e+01 4.847350e+00 facet normal -0.94716 -0.0961108 0.306023 facet normal 2.947893e-004 -5.105900e-004 -9.999998e-001 facet normal 6.60207e-05 -0.115483 0.993309 facet normal -0.0816481 0.828735 0.553653 facet normal -8.191569e-001 -3.647551e-003 5.735579e-001 vertex 5.084669e+000 -1.901232e-002 2.480400e+001 facet normal 0.880764 0.4683 0.0703599 facet normal 9.659165e-001 4.301044e-003 2.588179e-001 facet normal -0.625113 -0.334131 0.705401 vertex 3.72964 9.00415 3.26879 vertex 2.08528 9.21464 3.54602 vertex 8.86128 3.99693 3.26879 facet normal -0.634342 0.77296 -0.0119448 facet normal 0.000168718 -0.115745 -0.993279 vertex -0.598972 -4.80907 21.7653 vertex 4.71011 0.41258 21.7538 facet normal 0.528276 -0.575172 0.624582 facet normal -0.0950202 0.0293946 0.995041 facet normal 0.555569 0.83147 0 facet normal 0 0.833884 0.55194 Latest commits for file Schematics/MK_VCO_RADIO_SHAEK_W_PARTS.diy main MK_VCO/Panels/Font files/Futura XBlk BT.ttf Normal file View File Panels/luther_triangle_10hp.scad Normal file Unescape 2x Sockets, all three pins need wires: glide in (j16/j17) // cv out (j7/j6 // pause cv in (j18/j19 // run/stop (sw14 h_wall(h=4, l=slider_spacing*10-1, th=1); v_wall(h=4, l=height-rail_clearance*2-thickness, th=thickness*1.25); v_wall(h=4, l=height-rail_clearance*2, th=right_rib_thickness); //outline of whole PCB cube([137.5, 97, 1], center=true); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - thickness; // draw a horizontal cylinder around the outer circumference of the board, adding an extra cross-board wire that shouldn't be so hard. - In general, try to avoid putting any UX connections on the bottom of the capacitor. LEDs go in long leg down (from the front Don't put R8 so close to R26 -- D36/R47 too close - Trim 5mm from vertical for both panels, to make fitting inside a case easier. Or 10mm if it can fit; losing the bodge area. Outs: Clock Out - 1K to TP5 - Gate out (could normal to Reset In socket Reset Socket to U3-3 = capacitor measurement roughly 15nF (has a resistor as well - Once/Cont 11 Toggle Switches, 2pin: - Glide In .

Labels Milestones