Labels Milestones
BackThe knob. [mm] sphere_indents_center_distance = 12; hole_vdist = 44.5; hole_hdist = 65; hole_diameter = 2; center_adjust = 5; width_mm=90; height=16; thickness=2; label_inset_height = thickness-1; // Width of module (HP) width = 24; // [1:1:84] //Second row interface placement square_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - thickness*2.5 - tolerance*6; out_row_8 = working_increment*7 + out_row_1; rotary_knob_row = top_row - 30; left_rib_x = 0; right_rib_x = width_mm - thickness*2; // draw panel, subtract holes // label the whole thing? // top/bottom ribs? // top point? ]; From 32ece2d681b26731bad50902587b988d6a79e43e Mon Sep 17 00:00:00 2001 Subject: [PATCH] Bring in diylc and openscad design ## Mechanical assembly Regarding the board mounted potentiometers, there are two overlapping footprints provided for each, allowing you to use 7.5mm holes, not 6mm - alpha pots - 9.8mm, +2mm rotary - 11.5mm, +3.5mm -- biggest by far, maybe 12.6mm? Alpha pots: barely enough to attach knob 01bb4964a6 Add CV in to pause the sequence. Probably can't do, or impractical: CV-controlled clock. Presumably the CV in that pauses the clock 3c7abf2196 Go to file db7d02719b Find and replace last few thin traces, fix teardrops and gnd fill db7d02719b68f4d2f81a25d8b6527257f18cc3a1 Embiggen traces, add teardrops 46614f2341 Add 55k-ish resistor to coarse knob to fix - CV Range - Once/Cont 11 Toggle Switches, 2pin: - step - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below) - Clock In Normal - 1k to U2-8 (AND NOT short to U2-10 Clock Rate - variable resist +6k between U2-8 and U2-9 Reset Sw - when pressed, short +12V and Reset In - ~27K to U3-8? No, transistors maybe activate? - Clock rate (B100k) (not sure yet which 2 pins diameter 3.0mm z-position of LED center 2.0mm, 2 pins LED, diameter 5.0mm z-position of LED center 2.0mm 2 pins diameter 3.0mm z-position of LED center 1.0mm 2 pins diameter 5.0mm 2 pins diameter 5.0mm THT rectangular pad as test point, loop diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00012_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00299, 3 pins, pitch 5mm, size 60x12.6mm^2, drill diamater 1.2mm, pad diameter 2.2mm, see http://www.mouser.com/ds/2/324/ItemDetail_1725672-916605.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block WAGO 236-201 45Degree pitch 5mm size 17.3x14mm^2 drill 1.15mm pad 3mm Terminal Block 4Ucon ItemNo. 10698 vertical pitch 5mm size 22.3x14mm^2 drill 1.15mm pad 3mm Terminal Block Phoenix MKDS-3-8-5.08 pitch 5.08mm length 9mm width 3.6mm Capacitor C, Disc series, Radial, pin pitch=15.00mm, , length*width=16.5*11.8mm^2.
- Pitch=6.00*6.00mm^2, , length*width=11.5*11.5mm^2, Neosid.
- 3-pin PD-30S power DIN shielded Right-angle standard.
- Mount, https://www.neutrik.com/en/product/nl2md-v speakON Chassis Connectors.
- 2.5; slider_spacing = 12.5; // space between them.