Labels Milestones
Back= [h_margin, row_1, 0]; saw_out = [output_column, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; audio_out_2 = [right_col, row_5, 0]; audio_out_1 = [right_col, row_1, 0]; pwm_in = [input_column + h_margin/2, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_2, 0]; pwm_in = [input_column + h_margin/2, row_1, 0]; f_tune = [second_col, second_row, 0]; //Third row interface placement pwm_in = [width_mm - h_margin - working_width/8, row_2, 0]; pwm_in = [first_col, first_row, 0]; //Second row interface placement square_out = [width_mm-h_margin, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; fm_in = [first_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_2, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement f_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - thickness*2.5 - tolerance*6; left_rib_x = thickness + 6 + tolerance; // rib + half a jack col_right = width_mm - thickness; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - h_margin; cv_in = [h_margin, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; square_out = [third_col, fourth_row, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; pwm_duty = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; fm_in = [h_margin+working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_2, 0]; triangle_out = [third_col, fourth_row, 0]; //Fifth row interface placement f_tune = [second_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_2, 0]; audio_in_2 = [left_col, row_3, 0]; right_rib_x = width_mm - right_rib_thickness; Schematics/Dual_VCA.diy Normal file View File 3D Printing/Pot_Knobs/18-spline-pot-knob-indicator-line.stl Executable file View File Things best left to external modules: CV-controlled CV offset module - add a voltage to trigger steps. Replace.
- 1.5/3-H-3.5 Terminal Block, 1990818 (https://www.phoenixcontact.com/online/portal/gb/?uri=pxc-oc-itemdetail:pid=1990818.
- SW_SPDT_MSM SW 0 0 Y.