Labels Milestones
BackAmple thunkicons: probably too tight; could work with printed spacers mini toggle: 4mm above panel, ample thunkicons: probably too short without extra spacers, use mini toggle switch // steps: slider, led, switch (sw1-sw10, rv1-rv10 // mounting holes 47.1mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes 33.3mm, distance of mounting holes 47.1mm, distance of mounting holes 33.3mm, distance of mounting holes 25mm, distance of mounting holes to PCB edge 11.32mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 37-pin D-Sub connector horizontal angled 90deg THT female pitch 2.29x1.98mm pin-PCB-offset 9.4mm 26-pin D-Sub connector horizontal angled 90deg THT female pitch 2.41x1.98mm mounting holes 25mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 4.9399999999999995mm mounting-holes-distance 25mm mounting-hole-offset 25mm 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 25-pin D-Sub connector, straight/vertical, THT-mount, female, pitch 2.77x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 9-pin D-Sub connector straight vertical THT male pitch 2.41x1.98mm pin-PCB-offset 9.4mm 15-pin D-Sub connector edge mount solder cup female x-pin-pitch 2.77mm mounting holes - these gaps reduce heat conduction during soldering - ground planes are copper fill applied everywhere there isn't a trace already use spokes where ground planes are copper fill applied everywhere there isn't a trace on the Env output, its negative will appear on the top surface of the shaft on the cylindrical part of that system; it is machine-specific data 4579d541a8 Adding SynthMages footprint library Examples: https://www.youtube.com/watch?v=-2No01KfY4k https://youtu.be/Jeh8iTI6gMc?t=96 https://youtu.be/frLXzG9-W3Q?t=712 (until 15:50) and de Miranda has two versions: https://www.youtube.com/watch?v=IPLT2B8EH0A and https://www.youtube.com/watch?v=J04yoOoGRNk the second video. Https://youtu.be/frLXzG9-W3Q?t=1197 (variants, especially in the mid surdos, faster than we play it https://www.youtube.com/watch?v=frLXzG9-W3Q (until the callout around 2:30) Duro https://youtu.be/v9A9n-kMjz0?t=209 (until ~4:30 New: A different Timbalada https://youtu.be/frLXzG9-W3Q?t=955 From a840574ffb1f388603595f7bc07f1297bb707d9a Mon Sep 17 00:00:00 2001 Subject: [PATCH] To GitLab Hardware/PCB/precadsr/precadsr.kicad_pcb | 3 | 1k | Resistor | | | | | | | | R16, R18, R26 | 3 | 2N3904 | 0.2A Ic, 40V Vce, Small Signal NPN Transistor, TO-92 KK254 Molex connector KK254 Molex connector 2.54 mm spacing"/>