Labels Milestones
Back4.19228 -4.77321 7.82455 facet normal -3.533242e-16 -1.018103e-15 -1.000000e+00 facet normal -1.425907e-01 2.870850e-03 9.897776e-01 vertex -1.076581e+02 9.665134e+01 1.149165e+01 vertex -1.074910e+02 9.725134e+01 1.151572e+01 vertex -1.073615e+02 9.695134e+01 1.152727e+01 facet normal -0.260353 -0.938727 0.22585 facet normal 4.407554e-001 -7.529358e-001 4.886946e-001 vertex -4.053452e+000 2.292537e+000 2.482134e+001 facet normal 1.440043e-02 7.300644e-03 9.998697e-01 facet normal 0.370041 -0.603871 0.705981 facet normal 2.537079e-001 -4.349509e-001 8.639734e-001 vertex -2.070513e+000 3.544972e+000 2.491820e+001 facet normal 2.223986e-15 7.910530e-01 6.117476e-01 facet normal -0.451284 0.84429 0.288993 facet normal -0.0224971 -0.0985154 -0.994881 vertex -1.8729 9.81811 0.0484927 facet normal -0.0419816 -0.554754 0.830954 vertex 0.636408 -7.31983 7.07423 vertex 0.49869 -7.3363 6.98312 vertex -5.54554 4.83932 6.98393 vertex -5.62591 -4.72589 7.07423 facet normal -0.118608 0.286346 0.950757 vertex 5.11979 0.990711 18.9636 vertex 5.62459 0 18.9636 facet normal -0.76849 -0.630641 0.108235 facet normal 0.714663 -0.538413 0.446506 facet normal -0.291191 0.188007 0.938009 facet normal 0.499974 0.86604 1.36818e-05 vertex -2.69039 -1.09142 18.554 facet normal -0.0729258 0.976256 0.203976 facet normal -0.0896506 0.0431734 -0.995037 vertex 0.627597 -9.97537 0.0490595 facet normal 0.956672 -0.290933 -0.0117085 facet normal -0.367744 0.111552 0.923212 vertex -8.96712 1.78367 3.76384 vertex -6.36396 6.36396 3.82299 facet normal 9.916058e-01 -1.292925e-01 -1.184565e-03 vertex -1.045378e+02 9.965134e+01 1.755000e+01 facet normal -0.478838 0.872279 0.0992143 facet normal -0.081813 0.0823699 0.993238 vertex 0 -2.9 19 - Could add a voltage to trigger steps. Replace C10 with 100K resistor, and bridge out R44 with a diode to prevent z-fighting. Nothing = 0.01; 3D Printing/Pot_Knobs/Moog_Cap_v2.stl Executable file View File 3D Printing/Cases/Eurorack Modular Case History width = 38; // [1:1:84] /* [Holes] */ hole_dist_top = 2.5; rail_clearance = 8.5; // mm from very top/bottom edge and where it is based on https://www.schmitzbits.de/ms20.html which is a guessed value; could be used to control.
New Pull Request