synth_tools

Back

(8+tolerance/5); // generally-useful spacing amount for vertical columns of stuff center_adjust = 2.5; rail_clearance = 8.5; // mm from very top/bottom edge and where it is if your 3PDT toggle switch, like mine, is a combination of speakON socket and 6.35mm (1/4in) mono jack, switched, with chrome ferrule and offset PCB pins, https://www.neutrik.com/en/product/nmj6hhd2 Slim Jacks, 6.35mm (1/4in) stereo jack, switched, with half threaded nose, sleeve contact/front panel connection, https://www.neutrik.com/en/product/nrj4hh-1 Slim Jacks, 6.35mm (1/4in) jack receptacle, vertical pcb mount, https://www.neutrik.com/en/product/nlj2md-v speakON Chassis Connectors, 4 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3faav A Series, 3 pole male XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc4fav-0 A Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/ncj6fi-v-0 Combo I series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, lateral right PCB mount, https://www.neutrik.com/en/product/nc5fbh B Series, 3 pole female XLR receptacle, grounding: mating connector shell and front panel, lateral left PCB mount, retention spring, https://www.neutrik.com/en/product/ncj10fi-h Combo I series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3fah1 A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel: mini toggle: 4mm above panel, tight but possible micro toggle: probably too tight; could work with printed spacers mini toggle: 4mm above panel, tight but possible mini toggle: 4mm above panel, tight but possible mini toggle: 2.5mm above panel, tight but possible mini toggle: 4mm above panel, ample thunkicons: probably too tight; could work with printed spacers and existing lead lengths From b1fcba1e78f37669542b35a3e32a5257c5c0240c Mon Sep 17 00:00:00 2001 Subject: [PATCH 01/13] initial notes for v1 front panel design and includes 2.5mm centerward shift for input and send reset to clk_inh to stop progressing Add cascading input and output jacks input_column = h_margin; col_right = width_mm - h_margin; cv_in = [h_margin, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; c_tune = [second_col, second_row, 0]; //Third row interface placement pwm_in = [input_column + h_margin/2, row_1, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; audio_out_2 = [right_col, row_2, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; c_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = 0; // [0:No, 1:Yes] TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) + pow(KnobMajorRadius-KnobMinorRadius,2)))) .

New Pull Request

Labels Milestones