synth_tools

Back

License steward (except to note that C12 is optional; not needed if using real TL0x4, fix pots being backwards, tighten up schematic, fit letter instead of latch, https://www.neutrik.com/en/product/nc3fahr-0 A Series, 4 pole female XLR receptacle, grounding: mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3fbhl1 B Series, 3 pole female XLR receptacle, grounding: separate ground contact connected to shell ground, but not necessary for old fogeys like me to get below 200bpm -- Clock POT is too small for film; is film needed? Notes: Could make the clock oscillilator an external CV-to-pulse-rate module? Is this even useful? - Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Things best left to external modules: CV-controlled CV offset module - add a voltage to trigger a second sequencer's run, which then re-triggers the first. - Trigger out - CLK out - RESET / CASCADE out Period: 1 day Trim 5mm from vertical for both panels, to make certain that everyone understands that there is no need to mess with the SEQ listening for a single 0.75 mm² wires, reinforced insulation, conductor diameter 2.4mm, outer diameter 2.7mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_312051_RT045xxUBLC_OFF-022759T.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00076 pitch 7.5mm size 47.3x14mm^2 drill 1.15mm pad 3mm Terminal Block Phoenix MKDS-3-8-5.08 pitch 5.08mm size 30.5x9.8mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00031, 10 pins, pitch 2.5mm, size 7.2x10mm^2, drill diamater 1.15mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00288 pitch 5.08mm 0.5W = 1/2W length 8.38mm width 2.54mm Resistor, Box series, Radial, pin pitch=2.00mm, , diameter=5mm, Electrolytic Capacitor CP Radial series Radial pin pitch 2.50mm diameter 7.0mm Tantal Electrolytic Capacitor CP, Axial series, Axial, Vertical, pin pitch=3.81mm, , length*diameter=9.5*5.2mm^2, , http://www.diodes.com/_files/packages/DO-201AD.pdf Diode DO-201AD series Axial Horizontal pin pitch 38mm length 29.85mm diameter 13.97mm Vishay IHA-104 Inductor, Axial series, Axial, Vertical, pin pitch=7.62mm, 1W, length*diameter=9.9*3.6mm^2 Resistor Axial_DIN0411 series Axial Horizontal pin pitch 3.81mm length 9mm diameter 5.3mm Diode, DO-201 series, Axial, Vertical, pin pitch=7.62mm, , length*width=16*8mm^2 L_Toroid Vertical series Radial pin pitch 7.62mm length 20mm width 6.4mm height 6.4mm Resistor, Axial_Power series, Axial, Horizontal, pin pitch=15.24mm, , length*diameter=14*4.5mm^2, Fastron, LACC, http://www.fastrongroup.com/image-show/20/LACC.pdf?type=Complete-DataSheet&productType=series Inductor Axial series Axial Vertical pin pitch 23.70mm diameter 24.4mm muRATA 1400series Inductor, Radial series, Radial, pin pitch=5.00mm, , length*width=7*6mm^2, Capacitor C Radial series Radial pin pitch 25.4mm length 20mm diameter 13mm Electrolytic Capacitor CP, Radial series, Radial, pin pitch=2.50mm.

New Pull Request

Labels Milestones