synth_tools

Back

X="5.05" y="2.85"/> <-- CV In main MK_VCO/Panels/fireball_vco_14hp_v1.scad 330 lines width = 38; // [1:1:84] square_out = [output_column, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_4, 0]; left_rib_x = thickness * 2; right_rib_x = width_mm - h_margin; cv_in = [first_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; c_tune = [width_mm/2, top_row, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - hole_dist_side - thickness; // draw panel, subtract holes union() { difference(){ color([.1,.1,.1]) panel(width); // waves out // 1 for cv glide atten (rv15 // glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Clock POT is the two clockwise-most pins, looking from below. Clock rate (B100k) (not sure yet which 2 pins IR-ED, diameter 3.0mm, 2 pins LED_Rectangular, Rectangular, Rectangular size 5.0x2.0mm^2 2 pins LED, diameter 3.0mm, 3 pins, pitch 2.54mm, hole diameter 1.5mm THT rectangular pad as test Point, diameter 2.0mm, hole diameter 1.3mm, wire diameter 0.5mm test point wire loop as test point, pitch 5.08mm, size 66x11.2mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00287_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00054, 11 pins, pitch 5mm, size 80x9mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00013, 3 pins, pitch 7.5mm, size 67.5x10.3mm^2, drill diamater 1.2mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MPT-0,5-4-2.54 pitch 2.54mm size 25.86x6.5mm^2 drill 1.1mm pad 2.1mm terminal block Metz Connect Type067_RT01902HDWC, 2 pins, diameter 3.0mm z-position of LED center 2.0mm, 2 pins, pitch 5mm, size 40x10mm^2, drill diamater 1.15mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/2138224.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MKDS-1,5-15, 15.

New Pull Request

Labels Milestones