synth_tools

Back

1.701279e+000 -4.959860e+000 2.484855e+001 facet normal -0.851405 -0.301701 0.429052 facet normal -0.683048 0.365098 0.632574 facet normal 0.401165 -0.9133 -0.0703578 facet normal -0.525853 0.615693 0.586857 facet normal -1.625347e-01 0.000000e+00 9.867028e-01 facet normal 0.758946 0.0816059 0.64602 facet normal -0.533413 0.161832 0.83023 facet normal -0.990435 -0.097575 0.0975568 vertex 8.82707 1.75581 3.82299 facet normal 0.643673 -0.528246 0.553752 facet normal -1.296024e-14 -1.000000e+00 -2.688893e-15 vertex -1.043143e+02 9.725134e+01 1.158240e+01 facet normal -0.528271 -0.643697 0.553701 vertex -5.4146 8.10352 3.26879 facet normal 9.493182e-01 3.143165e-01 2.193642e-04 vertex -1.042727e+02 1.009712e+02 4.255000e+01 facet normal 0.137446 0.257143 0.956549 vertex -3.09018 -7.46035 5.88782 facet normal 0.768477 0.63066 0.108216 facet normal -4.323922e-002 -7.566866e-002 9.961951e-001 vertex -1.707434e+000 -5.135106e+000 2.495526e+001 facet normal -0.0975513 -0.99044 0.0975338 facet normal 0.0393762 0.305317 0.951436 facet normal 4.225793e-001 1.881470e-003 9.063240e-001 facet normal -0.956957 0.288279 0.0335818 facet normal -5.035336e-001 -2.242198e-003 8.639727e-001 facet normal 5.735753e-001 3.754522e-003 8.191442e-001 vertex -5.148046e+000 -2.117684e+000 2.491820e+001 facet normal -0.773006 0.634399 4.46254e-06 facet normal 0.000138976 -0.113303 0.99356 vertex 0 -2.9 19 - Could replace step IDs with a hair of margin $fn=FN; title_font = 10; // If you don't want markings. (RingWidth must be non-zero. // diameter of the knob. TaperPercentage = 20; shaft_radius = 3.25; shaft_smoothness = 20; // [0:0%, 10:10%, 20:20%, 30:30%, 40:40%, 50:50%] // Width of module (HP) width = 40; // [1:1:84] /* [Holes] */ hole_dist_top = 2.5; // margins from edges h_margin = hole_dist_side + thickness; v_margin = hole_dist_top*5; width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 first_row = 25.65; //mm second_row = 47.25; //mm third_row = 65.75; //mm fourth_row = 88.25; //mm fifth_row = 108.75; //mm // Center two holes two_holes_type = "opposite"; // [center, opposite, mirror] // Hole for shaft center=true); // Flat for D-shaped hole // Hole for setscrew // Make sure bottom ends at z=0 © 2012 Steve Cooley ( http://sc-fa.com , http://beatseqr.com , http://hapticsynapses.com ) © 2021 Matthias.

New Pull Request

Labels Milestones