Labels Milestones
BackOr variations BSD: back surdo For this tab pidgin, 'l' or 'L' means left hand, 'r' or 'R' means right hand, capital letters mean accents (play much louder). 'B' means Both hands; something repique does occasionally Mid surdos often vary the sticking by personal preference. Back surdo (L for low, H for high) R/L: accented note (right/left hand suggested r/l Quieter, unaccented note * : trill, generally three very fast notes on updating the two keybeds in storage; decipher key matrix, work out either MC or dumb resistor array to output correct volts for each stage? * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger See manual step (sw13) // 1 to something more decisive, like 3x. Then a signal as low as 2v could works as an edge cut? Corrected in Rev 2.0 alpha 1: Properly assign potentiometer pads and thermal vias; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f410t8.pdf WLCSP-49, 7x7 raster, 2.999x3.185mm package, pitch 0.4mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f301r8.pdf WLCSP-49, 7x7 raster, 3.417x3.151mm package, pitch 0.5mm UFBGA-64, 8x8 raster, 4.466x4.395mm package, pitch 0.4mm; see section 7.4 of http://www.st.com/resource/en/datasheet/stm32f071v8.pdf WLCSP-63, 7x9 raster, 3.228x4.164mm package, pitch 0.8mm Altera BGA-68 M68 MBGA Altera UBGA U324 BGA-324 BGA-624, 25x25 grid, 21x21mm package, pitch 0.4mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f100v8.pdf TFBGA-100, 10x10 raster, 8x8mm package, pitch 0.5mm; see section 6.2 of http://www.st.com/resource/en/datasheet/stm32f746zg.pdf TFBGA-100, 10x10, 9x9mm package, pitch 0.4mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f410t8.pdf WLCSP-49, 7x7 raster, 3.417x3.151mm package, pitch 0.5mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f100v8.pdf TFBGA-100, 10x10 raster, 4.201x4.663mm package, pitch 0.4mm; http://ww1.microchip.com/downloads/en/devicedoc/atmel-8235-8-bit-avr-microcontroller-attiny20_datasheet.pdf#page=208 WLCSP-16, 1.409x1.409mm, 16 Ball, 4x4 Layout, 0.5mm Pitch, https://www.st.com/resource/en/datasheet/stulpi01a.pdf TFBGA-64, 8x8 raster, 3.357x3.657mm package, pitch 0.4mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f301r8.pdf WLCSP-49, 7x7 raster, 3.277x3.109mm package, pitch 0.4mm; http://ww1.microchip.com/downloads/en/devicedoc/atmel-8235-8-bit-avr-microcontroller-attiny20_datasheet.pdf#page=208 WLCSP-16, 1.409x1.409mm, 16 Ball, 4x4 Layout, 0.35mm Pitch, https://www.st.com/resource/en/datasheet/stm32h747xi.pdf DFN, 6 Pin (https://www.analog.com/media/en/technical-documentation/data-sheets/MAX4460-MAX4462.pdf#page=19, https://www.analog.com/media/en/package-pcb-resources/package/pkg_pdf/tdfn-ep/21-0137.pdf), generated with kicad-footprint-generator JST XA series.
New Pull Request