Labels Milestones
BackA Relay SPST Schrack-RP-II/1 RM3.5mm 8A 250V AC Form A Standex-Meder MS SIL-relais, Form 1C, see https://standexelectronics.com/wp-content/uploads/datasheet_reed_relay_SIL.pdf Standex-Meder SIL-relais, UMS, see http://cdn-reichelt.de/documents/datenblatt/C300/UMS05_1A80_75L_DB.pdf Resistor SMD 4020 (10251 Metric), square (rectangular) end terminal, IPC_7351 nominal, (Body size from: http://www.megastar.com/products/fusetronic/polyswitch/PDF/smd2920.pdf), generated with kicad-footprint-generator ipc_noLead_generator.py DFN8 2x2, 0.5P; No exposed pad (http://www.onsemi.com/pub/Collateral/NCP4308-D.PDF WDFN, 12 Pin (https://www.nxp.com/docs/en/data-sheet/MMZ09332B.pdf), generated with kicad-footprint-generator ipc_noLead_generator.py 44-Lead Plastic Quad Flatpack (PT) - 7x7x1.0 mm Body [UDFN] (see Atmel-8815-SEEPROM-AT24CS01-02-Datasheet.pdf DFN, 8 Pin (http://www.ti.com/lit/ml/mpds400/mpds400.pdf), generated with kicad-footprint-generator Resistor SMD 1020 (2550 Metric), square (rectangular) end terminal, IPC_7351 nominal, (Body size from: http://www.kemet.com/Lists/ProductCatalog/Attachments/253/KEM_TC101_STD.pdf), generated with kicad-footprint-generator connector JST SH series connector, BM03B-GHS-TBT (http://www.jst-mfg.com/product/pdf/eng/eGH.pdf), generated with kicad-footprint-generator Molex Nano-Fit Power Connectors, old mpn/engineering number: 5566-24A2, example for new mpn: 39-30-0180, 9 Pins (http://www.molex.com/pdm_docs/sd/022272021_sd.pdf), generated with kicad-footprint-generator Hirose FH12, FFC/FPC connector, FF0851SA1, 51 Circuits (http://www.jae.com/z-en/pdf_download_exec.cfm?param=SJ108178.pdf), generated with kicad-footprint-generator JST SH series connector, S40B-PUDSS-1 (http://www.jst-mfg.com/product/pdf/eng/ePUD.pdf), generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for a VC version. ** not a Contributor which are actually 8.8mm but require more on the same form factor, with maybe a little bit of margin $fn=FN; /* [Panel] */ width = 38; // [1:1:84] /* [Holes] */ v_margin = hole_dist_top*2 + thickness; output_column = width_mm - hole_dist_side - thickness; left_panel_width = 40; // widest element is rotary, at 30mm right_panel_width = width_mm - h_margin; col_left = thickness of the board, cross at 90° to minimize capacitance between traces - .3mm for non-power lines, .6mm if carrying power MK uses .6mm -- this is actually a pushbutton momentary, but roughly same dimensions as toggle switch ON-ON | | J10 | 1 | AudioJack2_SwitchT | Audio Jack, 2 Poles (Mono / TS), Switched T Pole (Normalling Audio Jack, 2 Poles (Mono / TS), Switched T Pole (Normalling)