synth_tools

Back

Unescape Hardware/PCB/precadsr/fp-lib-table Normal file Unescape Hardware/Panel/precadsr_panel_al/precadsr_panel_al.pretty/Bigger_Push_Switch_Hole_NPTH.kicad_mod Normal file View File Schematics/notes.txt Normal file Unescape Mon 19 Apr 2021 10:22:18 AM EDT Mon 10 May 2021 12:33:34 AM EDT Sat 28 Aug 2021 07:18:14 PM EDT Generated from schematic by Eeschema 5.1.9-73d0e3b20d~88~ubuntu20.04.1 Generated from schematic into main 96f746fa2d Final tweaks, version submitted to JLCPCB on 20240124 Final tweaks, version submitted to JLCPCB on 20240124 Final tweaks, version submitted to JLCPCB on 20240124 63579cf959 Add notes about UX component wiring 2x Sockets, all three pins need wires: glide in (j16/j17 // cv range (sw12 // 1 for run/stop (sw14 h_wall(h=4, l=slider_spacing*10-1, th=1); v_wall(h=4, l=height-rail_clearance*2-thickness, th=2); h_wall(h=4, l=slider_spacing*10+left_panel_width/2-right_rib_thickness, th=1.5); main drumkit/Schematics/OttosIrresistableDance/OttosIrresistableDance.kicad_sch 1023 lines main synth_tools/Schematics/SynthMages.pretty/POT_2_PIN_Header.kicad_mod 44 lines main MK_SEQ/Schematics/notes.txt 35 lines Latest commits for file Fireball/Fireball_panel.kicad_pcb 972e45fb78 corrects inexplicably begreebled lower thre knob labels; confirms mask color is as defined replaces FIREBALL mask/etch with silkscreen replaces FIREBALL mask/etch with silkscreen caaf12f2da0fe056d0b625b9c1a860efbae9f4d1 adds ideas for a 1uF capacitor. 1uF may be brought only in 1000+ for these. Original README: * LEDs in sliders, lit for each stage? * TBD, needs testing; but if LEDs are possible, this should be enclosed in the front Don't put R8 so close to R26 D36/R47 too close - Trim 5mm from vertical for both panels, to make fitting inside a case easier. Or 10mm if it faces away and so on. // body - hole // handle + rest of body // knurled handle (requires https://www.thingiverse.com/thing:32122 //knurled_cyl( clf_partHeight, clf_handle_diameter, 2, 2, true, 10 ); // the first layer will be thinner than this foreach($imgs as $img){ $article['content'] .= "

" . $entry->textContent . "

"; } } module knurled_finish(ord, ird, lf, sh, fn, rn) { for(j=[0:rn-1]) assign(h0=sh*j, h1=sh*(j+1/2), h2=sh*(j+1)) { for(i=[0:fn-1]) assign(lf0=lf*i, lf1=lf*(i+1/2), lf2=lf*(i+1)) { polyhedron( points=[ [ 0,0,h0], [ ord*cos(lf0), ord*sin(lf0), h2], [ ird*cos(lf1), ird*sin(lf1), h2], [ ord*cos(lf2), ord*sin(lf2), h2] ], triangles=[ [0,1,2],[2,3,0], [1,0,4],[4,0,7],[7,8,4], [8,7,9],[10,9,7], [10,7,6],[6,7,0],[3,6,0], [2,1,4],[3,2,6],[10,6,9],[8,9,4], [4,5,2],[2,5,6],[6,5,9],[9,5,4] ], convexity=5); } } module eurorackMountHoles(php, holes, hw) { holes = holes-holes%2;// mountHoles ought to be fixed elsewhere Add.

New Pull Request

Labels Milestones