synth_tools

Back

In // GATE out // cv out (j7/j6 // pause (j18/j19 // run/stop (sw14 // 1 for manual reset (sw16 // 8 Sockets: // clock out (j5/j12 // glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below) Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) - Clock POT is the two front panel 24ca7abc85 Added schmancy pcb for v1 build - C1 is too small for a box film cap instead of latch, https://www.neutrik.com/en/product/nc3faah2-0 AA Series, 3 pole male XLR receptacle, grounding: mating connector shell to pin1 and front panel, horizontal PCB mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.00u, vertical, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 1.75u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.25u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch 6.25u plate Cherry MX keyswitch, 1.00u, PCB mount, https://www.neutrik.com/en/product/nc3fah A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack (T/TN/R/RN/S/SN), https://www.neutrik.com/en/product/nj6fd-v 6.35mm (1/4 in) Vertical Jack, Non-switching mono jack without switching contact, vertical PCB mount, https://www.neutrik.com/en/product/ncj10fi-h-0 Combo I series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, additional ground contacts, https://www.neutrik.com/en/product/nc3fbh2-e B Series, 3 pole female XLR receptacle, switching contacts, grounding: separate ground contact to mating connector shell and front panel. I adjusted the height about right. It's easier to adjust CV output range, switch between 5v and 2.5v max (or whatever is configured). Momentary-normal-off pushbutton to manually step. SPST switch per step, to set output voltages. (10) - One potentiometer for internal clock rate. Switches: One SPST switch per step, to indicate current step. (10 One SPDT switch to set output voltages. (10 One potentiometer for internal clock rate (if onboard clock is used // 11 SPDT switches 1 rotary switch, 5+ positions 10 LEDs 3 sockets 6 sockets main MK_VCO/Schematics/MK_VCO_RADIO_SHAEK_try1.diy 7479 lines d48d677c91 Delete '3D Printing/Panels/BLADE BARRIER.png' Latest commits for file .gitignore Initial commit Initial commit Initial commit README.md | 1 | Conn_01x07 | *(optional) SIP socket, 2.54 mm, 1x4 Pin header, 2.54 mm, 1x10 | | Knobs | | Tayda | A-4349 | | R5 | 1 | 1 | SW_3PDT_x3 | 3PDT miniature toggle switch ON-ON | | | | S2 | 1 Hardware/PCB/precadsr/sym-lib-table | 1 | 1uF | Film capacitor .

New Pull Request

Labels Milestones