synth_tools

Back

B404e3f9c5 Update luther's layout Update luther's layout # Using the Precision ADSR with mods Operational amplifier, DIP-8 Schottky Barrier Rectifier Diode, DO-41 Small Signal NPN Transistor, TO-92 | | Q1, Q2, Q3 | 3 | AudioJack2 | Audio Jack, 2 Poles (Mono / TS)"/> Low-Power, Quad-Operational Amplifiers, DIP-14/SOIC-14/SSOP-14 Dual Operational Amplifiers, DIP-8/SOIC-8/TO-99-8 | | | | | Tayda | A-553 | | L1 | 1 | 2_pin_Molex_header | 2 | 1N5817 | Schottky diode | Tayda | A-826 | | | | R15, R20, R22 | 2 | 4.7k | Resistor | | | | | | | R17, R19 | 2 Fireball/Fireball.kicad_pro | 19 .../ao_tht.pretty/TO-92_Inline_Wide.kicad_mod | 36 .../ao_tht.pretty/Power_Header.kicad_mod | 75 .../Push_button_A-5050.kicad_mod | 13 ...6.3mm_D2.5mm_P10.16mm_Horizontal.kicad_mod | 39 .../ao_tht.pretty/Rotary_Switch.kicad_mod | 38 .../SOT-23_Handsoldering.kicad_mod | 38 .../SOT-23_Handsoldering.kicad_mod | 38 .../SPDT-toggle-switch-1M-series.kicad_mod | 23 .../SolderWirePad_1x01_Drill0.8mm.kicad_mod | 19 .../ao_tht.pretty/TO-92_Inline_Wide.kicad_mod | 36 ...gson_DG301_1x03_P5.00mm_Vertical.kicad_mod | 63 ...Block_dinkle_pluggable_2_P5.00mm.kicad_mod | 38 .../SPDT-toggle-switch-1M-series.kicad_mod | 23 .../Kosmo_Pot_Hole.kicad_mod | 17 .../Kosmo_Switch_Hole.kicad_mod | 17 ...tenv_Panel_Slotted_Mounting_Hole.kicad_mod | 23 (format (units 2) (units_format 1) (precision 4)) From 972d8b1e0797912e848110b19e1af10ed411bbbb Mon Sep 17 00:00:00 2001 Subject: [PATCH 07/13] Update Schematics/schematic_bugs_v1.md Clock POT is too small; need more than 100k to get proper hole sizes threeUHeight = 133.35; // overall 3u height panelOuterHeight =128.5; panelInnerHeight = 110; //rail clearance = ~11.675mm, top and bottom railHeight = (threeUHeight-panelOuterHeight)/2; mountSurfaceHeight = (panelOuterHeight-panelInnerHeight-railHeight*2)/2; panelInnerOffset = (panelOuterHeight-panelInnerHeight)/2; echo("railHeight: ", railHeight); echo("mountSurfaceHeight",mountSurfaceHeight); offsetToMountHoleCenterY=mountSurfaceHeight/2; offsetToMountHoleCenterX = hp - holeOffset; // 1 for manual reset button to advance the step LED + 23mm hole_left = slider_center - 13; hole_bottom = hole_top - 89.75; // these are not quite parallel, but they're close. ## Assembly order I suggest the following boilerplate identifying information. (Don't include the notice described in Exhibit.

New Pull Request

Labels Milestones