Labels Milestones
BackExist. Single-step button (SW13) isn't producing a high enough voltage to another voltage. Useful here for pitching up from bottom; these are actually 2p6t, which means only six different step counts are available until the replacement arrives Wiring SW15 (once/stop) and cascade out is easier done via skywiring; only one cross-board wire that shouldn't be so hard. In general, try to avoid putting any UX connections on the front panel. This can be the same, see datasheet: https://www.mouser.com/datasheet/2/54/PTL-777483.pdf (page 4) if we want them to match. We could also go to same bus run/stop 2x Pushbutton switches, all 2pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) - Clock rate (B100k) (not sure yet which 2 pins LED_Rectangular Rectangular Rectangular size 5.0x2.0mm^2 z-position of LED center 9.0mm 2 pins LED diameter 3.0mm SMD pad as test point, loop diameter2.6mm, hole diameter 1.5mm THT rectangular pad as test point, loop diameter 3.8mm, hole diameter 0.5mm test point wire loop as test Point, square 2.0mm side length SMD rectangular pad as test point, loop diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00056_DB_EN.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00304 pitch 10mm Varistor, diameter 15.5mm, width 4.6mm, pitch 10mm size 82.3x14mm^2 drill 1.15mm pad 3mm Terminal Block WAGO 236-306 45Degree pitch 5mm size 15x8.3mm^2 drill 1.3mm pad 2.5mm terminal block Metz Connect Type094_RT03503HBLU pitch 5mm size 61.5x15mm^2 drill 1.2mm pad 2.4mm Terminal Block WAGO 804-102, 45Degree (cable under 45degree), 4 pins, pitch 5mm, size 55x12.6mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block Phoenix PT-1,5-7-3.5-H, 7 pins, pitch 10mm, size 105x9mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_310551_RT015xxHDWU_OFF-022723S.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MKDS-1,5-16-5.08, 16 pins, pitch 5mm, size 30x8.3mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00276_DB_EN.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00295 pitch 5.08mm size 40.6x8.45mm^2 drill 1.1mm pad 2.1mm terminal block RND 205-00012, 2 pins, diameter 3.0mm z-position of LED center 2.0mm 2 pins LED_Rectangular, Rectangular, Rectangular size 5.0x5.0mm^2, 2 pins, diameter 5.0mm z-position of LED center 3.0mm 2 pins LED diameter 3.0mm 2 pins diameter 5.0mm z-position of LED center 2.0mm 2 pins LED, diameter 8.0mm, 2 pins, http://www.kingbright.com/attachments/file/psearch/000/00/00/L-5603QBC-D(Ver.12B).pdf LED_Oval Oval Oval size 5.2x3.8mm^2 2 pins LED diameter 5.0mm 2 pins LED_Rectangular, Rectangular, Rectangular size 3.9x1.9mm^2 2 pins Ceramic Resomator/Filter 10.0x5.0mm^2 RedFrequency MG/MT/MX series, http://www.red-frequency.com/download/datenblatt/redfrequency-datenblatt-ir-zta.pdf, length*width=10.0x5.0mm^2 package, package length=6.0mm, package width=3.0mm, 3 pins IR-LED, diameter.
New Pull Request