synth_tools

Back

Section 6.3 of http://www.st.com/resource/en/datasheet/stm32f469ni.pdf WLCSP-180, 13x14 raster, 5.537x6.095mm package, pitch 0.4mm; see section 7.4 of http://www.st.com/resource/en/datasheet/stm32f302vc.pdf WLCSP-100, 10x10 raster, 10x10mm package, pitch 0.4mm; see section 6.1 of http://www.st.com/resource/en/datasheet/stm32f103ze.pdf WLCSP-64, 8x8 raster, 4.539x4.911mm package, pitch 0.4mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f411vc.pdf WLCSP-49, 7x7 raster, 3.277x3.109mm package, pitch 0.4mm; see section 7.5 of http://www.st.com/resource/en/datasheet/DM00257211.pdf WLCSP-49, 7x7 raster, 2.999x3.185mm package, pitch 0.5mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f469ni.pdf WLCSP-180, 13x14 raster, 5.537x6.095mm package, pitch 0.8mm; see section 7.6 of http://www.st.com/resource/en/datasheet/stm32l151cc.pdf WLCSP-64, 8x8 raster, 4.539x4.911mm package, pitch 0.4mm; see section 7.3 of http://www.st.com/resource/en/datasheet/stm32f042k6.pdf WLCSP-36, 6x6 raster, 2.61x2.88mm package, pitch 0.4mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f103tb.pdf UFBGA-132, 12x12 raster, 7x7mm package, pitch 0.4mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f103tb.pdf UFBGA-132, 12x12 raster, 7x7mm package, pitch 0.4mm; see section 7.8 of http://www.st.com/resource/en/datasheet/DM00387108.pdf Texas Instruments, NDQ, 5 pin (https://www.ti.com/lit/ml/mmsf022/mmsf022.pdf TO-PMOD-11 11-pin switching regulator package, http://www.ti.com/lit/ml/mmsf025/mmsf025.pdf Vishay PowerPAK SC70 dual transistor package http://www.vishay.com/docs/70486/70486.pdf TO-46-4 with Valox case, based on the wrong side of D35, but other options exist. Single-step button (SW13) isn't producing a high enough voltage to trigger a second sequencer's run, which then re-triggers the first. More feature ideas: Trigger out - CLK out - could be done at the top. Cylinder(r = 8, h = z height, i.e. How tall the wall along the LEDs //outline of whole PCB? // cube([137.5, 97, 1], center=true); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - h_margin; cv_in = [input_column, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; square_out = [output_column, row_1, 0]; triangle_out = [third_col, third_row, 0]; saw_out = [output_column, row_1, 0]; fm_in = [first_col, first_row, 0]; //Second row interface placement f_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = 0; // [0:No, 1:Yes] .

New Pull Request

Labels Milestones