Labels Milestones
Back| 4890 width = 12; // overkill; currently three 3.5mm jacks needing 8mm //calculated x value of exact middle of slider panel (between steps 5 and 6 // manual reset (sw16 // clock out (j5/j12) // glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below - Glide, manual (A100k) (two left pins, from below Clock rate (B100k) (not sure yet which 2 pins LED_Rectangular Rectangular Rectangular size 5.0x2.0mm^2 z-position of LED center 1.0mm 2 pins LED_Rectangular Rectangular Rectangular size 4.5x1.6mm^2, 2 pins, pitch 5mm, size 41.5x15mm^2, drill diamater 1.15mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MKDS-3-5-5.08, 5 pins, pitch 2.54mm, size 25.9x6.2mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00078_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix PTSM-0,5-8-2.5-V-THR, vertical (cable from top), 6 pins, pitch 5mm, size 47.3x14mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00298_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block Metz Connect 360273 size 5x4mm^2 drill 1.5mm pad 3mm REDCUBE THR with internal through-hole thread WP-THRBU (https://www.we-online.de/katalog/datasheet/74650073.pdf screw terminal block connector http://www.phoenixcontact.com/us/products/1778696/pdf 2.5mm vertical SMD spring clamp terminal block RND 205-00003, 4 pins, pitch 2.54mm, size 10.6x6.2mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.mouser.com/ds/2/324/ItemDetail_1935161-922578.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_4Ucon THT Terminal Block Phoenix MKDS-1,5-11 pitch 5mm size 26.5x15mm^2 drill 1.2mm pad 2.4mm Terminal Block Phoenix MKDS-1,5-15-5.08 pitch 5.08mm size 81.3x9.8mm^2 drill 1.3mm pad 2.5mm terminal block Metz Connect Type055_RT01503HDWU, 3 pins, pitch 5.08mm, size 40.6x10.6mm^2, drill diamater 1.1mm, pad diameter 2.8mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_310111_RT055xxHBLC_OFF-022717S.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block Phoenix MKDS-1,5-8-5.08, 8 pins, pitch 10mm, size 55x10.3mm^2, drill diamater 1.3mm, pad diameter 3mm, see http://www.metz-connect.com/de/system/files/METZ_CONNECT_U_Contact_Katalog_Anschlusssysteme_fuer_Leiterplatten_DE_31_07_2017_OFF_024803.pdf?language=en page 133, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00024.
- -0.288339 0.956937 0.0336393 facet normal.
- -0.072938 -0.0676765 -0.995038 vertex -5.35356 8.44037 0.0482573.