synth_tools

Back

For Pause (J19/J18); the schematic is incorrect Ins: Clock In - U1-13 (can get at from top when assembled - Stop Switch - 10 - center_adjust; center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [h_margin, row_1, 0]; audio_out_2 = [right_col, row_7, 0]; cv_in_1b = [right_col, row_5, 0]; cv_in_2a = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_5, 0]; audio_out_1 = [right_col, row_5, 0]; audio_out_1 = [right_col, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; saw_out = [third_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; square_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness + 6 + tolerance; rotate_vector_cos = 0.94; // 'x' of 20 degree rotation rotate_vector_sin = 0.34; // 'y' of rotation left_edge = -rotate_vector_sin * rail_depth; right_edge = height - v_margin*2 - title_font_size*1.5; working_height = height - hole_dist_top); cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - 9.5/2 - right_rib_thickness - tolerance; // rib + half a jack col_right = width_mm - thickness*2; // draw a "vertical" wall to mount the circuit board to, dead center pcb_holder(h=10, l=top_row-rail_clearance*2, th=1.15, wall_thickness=1); // lower h-rib reinforcer cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - thickness*2.5 - tolerance*6; out_row_8 = working_increment*7 + out_row_1; rotary_knob_row = top_row - 30; //special-case the top square(smoothing_radius+pad,smoothing_radius+pad); rotate_extrude(convexity=10, $fn = sphere_indents_faces); height = 266 + tolerance; rotate_vector_cos = 0.94; // 'x' of 20 degree rotation rotate_vector_sin = 0.34; // 'y' of rotation left_edge = -rotate_vector_sin * rail_depth; right_edge = height - v_margin; working_increment = working_height / (8+tolerance/3); // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 1; right_rib_x = width_mm - h_margin; cv_in = [first_col, first_row, 0]; //Second row interface placement f_tune = [h_margin+working_width/8, row_2, 0]; cv_2b_atten = [right_col, row_2, 0]; fm_in = [h_margin+working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, first_row, 0]; sync_in = [first_col, fifth_row, 0]; square_out = [third_col, third_row, 0]; saw_out = [third_col, fifth_row, 0]; //left_rib_x = thickness * 2; right_rib_x = width_mm - thickness*2.5 - tolerance*6; left_rib_x = thickness + 9.5/2 + tolerance*2.

New Pull Request

Labels Milestones