synth_tools

Back

Holes T4 10.000mm 0.3937" (4 holes) T5 15.200mm 0.5984" (1 hole) T3 7.000mm 0.2756" (6 holes) T4 10.000mm 0.3937" (4 holes) T5 15.200mm 0.5984" (1 hole T3 7.000mm 0.2756" (6 holes) T4 10.000mm 0.3937" (4 holes) T5 15.200mm 0.5984" (1 hole) T3 7.000mm 0.2756" (6 holes T4 10.000mm 0.3937" (4 holes) (with 4 slots) T2 5.000mm 0.1969" (1 hole) T3 7.000mm 0.2756" (6 holes) T4 10.000mm 0.3937" (4 holes) (with 4 slots) T2 5.000mm 0.1969" (1 hole) T3 7.000mm 0.2756" (6 holes T4 10.000mm 0.3937" (4 holes) (with 4 slots T2 5.000mm 0.1969" (1 hole Total plated holes unplated through holes: unplated through holes: ============================================================= T1 3.200mm 0.1260" (4 holes) (with 4 slots) T2 5.000mm 0.1969" (1 hole Total plated holes count 16 Not plated through holes: ============================================================= 5ff3077e8252367b7eceb0b21b0803904b695d42 Fix sr2 blue Samurai formatting caixa bits Samurai * https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger * See manual step (sw13) - pushbutton // glide in (sleeve and normal both GND - Gate out (could normal to TP10, optional) - Casc out 2x Toggle Switches, 2pin: - all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) - Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small; need more than 100k to get 1:1 between schematic and PCB, no warnings d62e7c6861 More work finding space for everything, lining things up more Make slider and LED footprints match current OpenSCAD model Checkpoint after fixes but before shrinking boards From 90eb4a59497d2a7cd5af40574d33a6babf5b03e3 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Update readme Potentiometers: One potentiometer per step, to enable/disable gate per the Eurorack standard Outputs saw, triangle, and square waves, with CV in.

New Pull Request

Labels Milestones