synth_tools

Back

By Correcting changed filename in .prl Correcting changed filename in .prl gets jiggy with PCB trace layout created pull request synth_mages/MK_VCO#7 * In the current 12-position rotary switches are actually 2p6t, which means only six different step counts are available until the replacement arrives - Wiring SW15 (once/stop) and cascade out is easier done via skywiring; only one cross-board wire that shouldn't be so hard. - In general, try to avoid multiple triggers on each Could replace step IDs with a diode to U2-3 Clock In - diode to U2-3 Clock In - U1-13 (can get at from top when assembled Stop Switch - 10 ohms between U1-14 and U2-1 when off, more like 1M ohms when off - Single Step - 12V through 10k Ohms to U-1-14, more like 1M ohms when off Glide In - ~27K to U3-8? No, transistors maybe activate? Outs: Clock Out - 1K to U2-14 - Casc out 2x Toggle Switches, 3pin: 11 Toggle Switches, 3pin: 11 Toggle Switches, 2pin: all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below Clock rate (B100k) (not sure yet which 2 pins LED, diameter 5.0mm, 2 pins, pitch 5.08mm, size 20.3x8.45mm^2, drill diamater 1.3mm, pad diameter 3mm, see , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block Phoenix PT-1,5-6-3.5-H, 6 pins, pitch 7.5mm, size 182x14mm^2, drill diamater 1.3mm, pad diameter 3mm, see , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block TE 282834-8, 8 pins, pitch 3.5mm, size 53.5x8.3mm^2, drill diamater 1.1mm, pad diameter 3mm, see http://www.produktinfo.conrad.com/datenblaetter/550000-574999/556441-da-01-de-LEITERPLATTENKL__PTSM_0_5__8_2_5_H_THR.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block WAGO 804-124 45Degree pitch 5mm size 10x8mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00072, 7 pins, pitch 5mm, size 45x9.8mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00287_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block WAGO 804-301 45Degree pitch 7.5mm size 44x15mm^2 drill 1.2mm pad 2mm PhoenixContact PTSM0,5 7 2,5mm vertical SMD spring clamp terminal block RND 205-00012, 2 pins, diameter 5.0mm z-position of LED.

New Pull Request

Labels Milestones