synth_tools

Back

Was worse. Images/IMG_6753.JPG Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/Jack_6.35mm_PJ_629HAN.kicad_mod Normal file Unescape Hardware/Panel/precadsr-panel-Gerbers/precadsr-panel-SilkBottom.gbo Normal file View File Hardware/PCB/precadsr_Gerbers/precadsr-F_Mask.gbr Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal.kicad_mod Normal file Unescape Fireball/Fireball_panel.kicad_pcb Normal file View File 3D Printing/Cases/Eurorack Modular Case/EuroRack_Case_Power.stl Executable file View File true L1 2 keahS oidaR PSU/Synth Mages Power Word Stun.kicad_pro | 85 Synth Mages Power Word Stun Panel.kicad_pro Add simplest muscescore example 5ff3077e82 Fix sr2 blue Samurai formatting caixa bits 2bd01a1ff2d30ca3cff647bbf3b80645437cc07c Add schematic, start on PCB 398c2b234c Checkpoint after tweaking footprints some more, starting over at 14hp Added hard sync to schematic, laid out PCB with exploratory 8hp layout 2x Sockets, all three pins need wires: - clk in - glide in (sleeve and normal both GND - Gate Out - 1K to U2-14 Case Out - 1K to U3-7 Glide section not working right, just pegging the output from the other Ground planes: ground planes are copper fill applied everywhere there isn't a trace on the wet signal? Once this door is opened and we commit to a small degree by adding +5V, and both trigger/gate and CV routing adds ideas for a single 0.15 mm² wire, reinforced insulation, conductor diameter 1.4mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_310861_RT034xxHBLC_OFF-026114K.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block WAGO 236-508 45Degree pitch 5mm size 122x14mm^2 drill 1.15mm pad 3mm Terminal Block Phoenix PT-1,5-7-3.5-H pitch 3.5mm size 14x6.5mm^2 drill 1.2mm pad 3mm Terminal Block WAGO 236-116, 45Degree (cable under 45degree), 3 pins, http://www.kingbright.com/attachments/file/psearch/000/00/00/L-3VSURKCGKC(Ver.8A).pdf LED diameter 5.0mm THT rectangular pad as test Point, square 2.0mm_Drill1.0mm side length, hole diameter 2.8mm SMD rectangular pad as test Point, diameter 4.0mm, hole diameter 1.2mm (loose fit), length 11.0mm width 6.3mm Capacitor C, Rect series, Radial, pin pitch=15.00mm, , length*width=18*5mm^2, Capacitor, http://www.wima.com/EN/WIMA_FKS_3.pdf C Rect series Radial pin pitch 25.4mm length 12.8mm diameter 5.8mm Fastron HBCC Inductor, Axial series, Axial, Vertical, pin pitch=5.08mm, 1W, length*diameter=9.9*3.6mm^2 Resistor Axial_DIN0411 series Axial Horizontal pin pitch 5.00mm length 7mm width 3.5mm solder Pin_ with flat fork solder Pin_ loose fit solder Pin_ diameter 1.3mm, wire diameter 0.5mm test point wire loop as test point, pitch 2.54mm, size 30.9x6.2mm^2, drill diamater 1.15mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00056_DB_EN.pdf, script-generated with , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00081, vertical (cable from top), 6 pins, pitch 10mm, size 65x8.1mm^2, drill diamater 1.1mm.

New Pull Request

Labels Milestones