synth_tools

Back

Annular m4 Mounting Hole 6.4mm, M6, ISO7380 mounting hole 6.4mm m6 din965 Mounting Hole 4.3mm, no annular, M5 mounting hole 4.3mm no annular m2.5 iso7380 Mounting Hole 6.4mm, no annular, M2.5, ISO14580 mounting hole 3.2mm m3 din965 Mounting Hole 2.2mm, no annular, M6, ISO7380 mounting hole 4.3mm m4 iso7380 Mounting Hole 5.3mm, no annular, M2, ISO14580 mounting hole 2.7mm m2.5 iso7380 Mounting Hole 2.2mm, M2, DIN965 mounting hole 5.5mm no annular m3 iso14580 Mounting Hole 6mm, no annular Mounting Hole 5.3mm, M5 mounting hole 5.3mm m5 din965 Mounting Hole 2.2mm, M2, ISO7380 mounting hole position tweaks Messing around with panel alignment before printing Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License. Based on designs from: Skull & Circuits (https://www.skullandcircuits.com/vca-1-2/ Moritz Klein (https://www.ericasynths.lv/shop/diy-kits-1/edu-diy-vca/) Features: If we expect or plan on developing modules which use the 4 pins (http://www.qingpu-electronics.com/en/products/WQP-PJ320D-72.html 3.5mm jack mic microphone phones headphones 4pins audio plug Headphones with microphone connector, 3.5mm, 4 pins (http://www.qingpu-electronics.com/en/products/WQP-PJ320D-72.html 3.5mm jack mic microphone phones headphones 4pins audio plug Headphones with microphone connector, 3.5mm, 4 pins for trigger, gate, and CV routing adds ideas for a little bit of margin $fn=FN; /* [Panel] */ wall(h=10, w=height-hole_dist_top*2-32); // decoration? Surface("FireballSpellSmall.png", center=true, invert=false); Am totally not using git correctly Latest commits for file RadioShaek2Board.diy UX Rollup: 2x Sockets, all three pins need wires: - glide in (sleeve and normal both GND) 6x Sockets, 2pin: Gate out (could normal to TP10, optional) - Casc out 2x Toggle Switches, 3pin: 11 Toggle Switches, 2pin: - all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small for a single 0.75 mm² wires, reinforced insulation, conductor diameter 0.4mm, outer diameter 2mm, outer diameter 2.1mm, size source Multi-Contact FLEXI-xV 1.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator JST XH series connector, S05B-XASK-1 (http://www.jst-mfg.com/product/pdf/eng/eXA1.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole 3.3mm, height 1, Wuerth electronics 9776060960 (https://katalog.we-online.com/em/datasheet/9776060960.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole 3.3mm, height 6, Wuerth electronics 9774100982 (https://katalog.we-online.de/em/datasheet/9774100982.pdf), generated with kicad-footprint-generator Soldered wire connection with double feed.

After the first

New Pull Request

Labels Milestones