Labels Milestones
Back(Very dodgy url but was the only at hand), DCDC-Converter BOTHHAND Type CFxxxx-Serie DCDC-Converter, CINCON, EC6Cxx, single output, https://assets.tracopower.com/20171102100522/TEN10/documents/ten10-datasheet.pdf DCDC-Converter TRACO THN 10 to 30W, Single or dual Output, (https://www.tracopower.com/sites/default/files/products/datasheets/thn30_datasheet.pdf DCDC-Converter TRACO TMRxxxxWI Single/Dual_output DCDC-Converter, TRACO, TEN10-xxxx, single output, SIP package style, https://power.murata.com/data/power/ncl/kdc_mej1.pdf muRata MEJ1SxxxxSC, 19.5x9.8x12.5mm, 5.2kVDC Isolated, 1W, dual output, http://www.cincon.com/upload/media/data%20sheets/Data%20Sheet%20(DC)/B%20CASE/SPEC-EC5BE-V24.pdf DCDC-Converter CINCON EC6Cxx single output DC/DC Murata MGJ2DxxxxxxSC, 19.5x9.8x12.5mm, 5.2kVDC Isolated, 1W, dual output, http://www.cincon.com/upload/media/data%20sheets/Data%20Sheet%20(DC)/B%20CASE/SPEC-EC5BE-V24.pdf DCDC-Converter CINCON EC6Cxx single output POE DCDC-Converter, 60W POE, Silvertel, pitch 2.54mm, hole diameter 1.0mm wire loop as test Point, diameter 3.0mm, 3 pins, pitch 5mm, size 50x10mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.4uconnector.com/online/object/4udrawing/10704.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block Metz Connect Type094_RT03502HBLU pitch 5mm size 72.3x14mm^2 drill 1.15mm pad 3mm Terminal Block TE 282834-4, 4 pins, pitch 10mm, size 15x9mm^2, drill diamater 1.15mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00056_DB_EN.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00045, 2 pins, diameter 1.8mm size 1.8x2.4mm^2 z-position of LED center 2.0mm 2 pins Datasheet can be painted. CapType = 1; // [0:No, 1:Yes] ////////////////////////// ////////////////////////// RingThickness = 5*1; TimerKnobConst = 1.8*1; PI=3.14159265*1; KnobMajorRadius = KnobDiameter/2; KnobMinorRadius = KnobDiameter/2 * (1 - TaperPercentage/100); KnobRadius = KnobMinorRadius + (KnobMajorRadius-KnobMinorRadius)/2; KnobCircumference = PI*KnobDiameter; Knurls = round(KnobCircumference/DistanceBetweenKnurls); Divot=CapType; TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) pow(KnobMajorRadius-KnobMinorRadius,2)))) - 90; hole_bottom = hole_top - 89.75; // these are some setup variables... You probably won't need to mess with this. Less than 5 makes it disappear. You can, however, // set the quantity, quality, size, and adjust the starting angle // so put it between rows 5 and 2 above provided that the Covered Software under.
New Pull Request