Y="1.4"/> 2 keahS oidaR Update luther's layout # Using the Precision ADSR with retriggering and looping modifications * Bourns PTL series, such as: ** Would need another supplier, mouser sells only in 1000+ for these. Original README: * LEDs in sliders, lit for each Contribution on the left sub-panel top_row = height - v_margin - title_font_size*1.5; top_row = height - v_margin - title_font_size*2; saw_out = [h_margin + working_width/4, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; pwm_duty = [input_column, bottom_row, 0]; pwm_duty = [second_col, fourth_row, 0]; pwm_cv_lvl = [second_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_2, 0]; fm_in = [first_col, third_row, 0]; saw_out = [output_column, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; square_out = [width_mm-h_margin, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; triangle_out = [third_col, fifth_row, 0]; pwm_duty = [input_column, row_2, 0]; triangle_out = [output_column, row_2, 0]; triangle_out = [output_column, bottom_row, 0]; c_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness + 6 + tolerance; // rib + half a jack col_right = width_mm - col_right - thickness; left_panel_width = 12*3 + tolerance*2; // rib + half a jack col_right = width_mm - hole_dist_side - thickness; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - thickness*2.5 - tolerance*6; out_row_8 = working_increment*7 + out_row_1; out_row_5 = out_working_increment*4 + out_row_1; out_row_6 = working_increment*5 + out_row_1; out_row_3 = out_working_increment*2 + out_row_1; out_row_3 = out_working_increment*2 + out_row_1; out_row_4 = out_working_increment*3 + out_row_1; out_row_4 = working_increment*3 + row_1; row_3 = working_increment*2 + row_1; row_4 = working_increment*3 + out_row_1; //special-case the knob main shape. [mm] /* [Stem (optional)] */ // // Whether to create a dial, protruding from the centerline of the stem. ≥30 means "round, using current quality setting". // --------------------------------- // Enable rounding of the hole in case you are using an odd number of pins: 04; pin pitch: 3.50mm; Angled; threaded flange || order number: 1829219 12A 630V Generic Phoenix Contact connector footprint for: MSTB_2,5/10-GF-5,08; number of pins: 02; pin pitch: 3.50mm; Vertical; threaded flange || order number: 1777206 12A Generic Phoenix.
alt
click/enter