Labels Milestones
BackKeyswitch, 2.75u, http://matias.ca/switches/ Matias ALPS keyswitch 2.25u plate Cherry MX keyswitch 2.00u PCB Cherry MX keyswitch, 2.00u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.75u, http://matias.ca/switches/ Matias ALPS keyswitch 2.75u plate Cherry MX keyswitch, 1.25u, PCB mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 1.75u, http://matias.ca/switches/ Matias ALPS keyswitch 2.75u plate Cherry MX keyswitch 2.00u PCB Cherry MX keyswitch 2.75u PCB Cherry MX keyswitch 2.00u PCB Cherry MX keyswitch 6.25u PCB Cherry MX keyswitch 2.00u vertical plate Cherry MX keyswitch, 1.50u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch 2.00u Matias/ALPS keyswitch, 1.25u, PCB mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch 6.25u PCB Cherry MX keyswitch 1.25u PCB Cherry MX keyswitch, 2.00u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.00u, vertical, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.25u, PCB mount, https://www.neutrik.com/en/product/nl8md-v STX Series, 4 pole chassis connector, nickel metal square G-size flange, self tapping screw holes (A-screw), vertical PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc5mbh-b B Series, 3 pole male XLR receptacle, switching contacts, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3fav1-0 A Series, Chassis connector Phoenix H male (A series layout), horizontal PCB mount, https://www.neutrik.com/en/product/nc3faav2 AA Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc5fav-da A Series, 4 pole female XLR receptacle, grounding: mating connector shell to pin1 and front panel, vertical PCB mount, retention spring, https://www.neutrik.com/en/product/ncj10fi-h Combo I series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, switched, gold plated contacts, efficient chassis ground connection, T+R normalling contact, https://www.neutrik.com/en/product/nrj6hm-1-au Slim Jacks, 6.35mm (1/4in) mono jack, switched, with chrome ferrule and offset PCB pins, https://www.neutrik.com/en/product/nmj4hcd2 M Series, 6.35mm (1/4in) switching stereo jack (T/R/S), https://www.neutrik.com/en/product/nj3fd-v 6.35mm (1/4 in) Vertical Jack, 3 x 6mm drills 3 pin Molex header 2.54 mm spacing | Tayda | A-3588 | | | | R4, R6, R7 | 2 Hardware/lib/Kosmo_panel | 1 | 1 C10, C14 too small for film; is film needed? Notes: Could make the clock oscillilator an external CV-to-pulse-rate module? Is this even useful? Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Things best left to external modules: - CV-controlled CV offset module - add a global/master pitch control/modulation function with a diode matrix.
New Pull Request