Labels Milestones
BackHsh >= 0 module knurled_finish(ord, ird, lf, sh, fn, rn) { for(j=[0:rn-1]) assign(h0=sh*j, h1=sh*(j+1/2), h2=sh*(j+1)) { for(i=[0:fn-1]) assign(lf0=lf*i, lf1=lf*(i+1/2), lf2=lf*(i+1)) { polyhedron( points=[ [ 0,0,h0], [ ord*cos(lf0), ord*sin(lf0), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ord*cos(lf0), ord*sin(lf0), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ ord*cos(lf1), ord*sin(lf1), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ord*cos(lf1), ord*sin(lf1), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ord*cos(lf1), ord*sin(lf1), h1], [ ord*cos(lf0), ord*sin(lf0), h2], [ ird*cos(lf1), ird*sin(lf1), h0], [ ord*cos(lf2), ord*sin(lf2), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ 0,0,h2], [ ord*cos(lf0), ord*sin(lf0), h2], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ ord*cos(lf0), ord*sin(lf0), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ 0,0,h2], [ ord*cos(lf0), ord*sin(lf0), h0], [ ord*cos(lf2), ord*sin(lf2), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ 0,0,h2], Created on Tue Mar 5 20:19:51 2024 L1 : F.Cu front L2 : B.Cu back Drill file 'precadsr-panel.drl' contains T1 3.200mm 0.1260" (4 holes) (with 4 slots T2 5.000mm 0.1969" (1 hole) T3 7.000mm 0.2756" (6 holes) T4 10.000mm 0.3937" (4 holes T5 15.200mm 0.5984" (1 hole Total plated holes count 16 Not plated through holes: merged pull request synth_mages/MK_VCO#5 Final revision; added custom DRC as project file ad96459571a569a983e452184e49702fe8779c4e Merge pull request synth_mages/MK_VCO#3 From 3d0ca7fdf6e2ad8d7864221e585c668e46544055 Mon Sep 17 00:00:00 2001 Subject: [PATCH] More tweaks after pro review main arrasta/Samba_Reggae_1.html 62 lines footprint "Perfboard_4x12" (version 20221018) (generator pcbnew footprint "SLIDE_POT_0547" (version 20221018) (generator pcbnew Docs/precadsr_bom.md Normal file Unescape Hardware/Panel/precadsr-panel/precadsr-panel.kicad_pro Normal file Unescape // Width of "dial" ring (in mm). If you don't need to mess with them. // this is actually a pushbutton momentary, but roughly same dimensions as toggle switch // steps: slider, led, switch (sw1-sw10, rv1-rv10 // mounting holes 63.5mm, distance of mounting holes distance 63.5mm 37-pin D-Sub connector horizontal angled 90deg THT female pitch 2.41x1.98mm pin-PCB-offset 3.0300000000000002mm mounting-holes-distance 33.3mm mounting-hole-offset 33.3mm 15-pin D-Sub connector, straight/vertical, THT-mount, female, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 9-pin D-Sub connector horizontal angled 90deg THT female pitch 2.41x1.98mm pin-PCB-offset 8.35mm mounting-holes-distance 33.3mm mounting-hole-offset 33.3mm 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.41x1.98mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x1.98mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 9.9mm, distance of mounting holes distance 47.1mm 25-pin D-Sub connector horizontal angled 90deg THT male pitch 2.29x2.54mm pin-PCB-offset 9.4mm 25-pin D-Sub connector straight vertical THT female pitch 2.41x1.98mm pin-PCB-offset 9.4mm 15-pin D-Sub connector.
New Pull Request