synth_tools

Back

"preview"; // ["fast preview", "preview", "rendering", "final rendering"] // Top left: clock in, speed pot_p160(); // Left side: meta-step controls // run/stop (sw14 h_wall(h=4, l=slider_spacing*10-1, th=1); v_wall(h=4, l=height-rail_clearance*2-thickness, th=thickness*1.25); v_wall(h=4, l=height-rail_clearance*2, th=right_rib_thickness); //outline of whole PCB cube([137.5, 97, 1], center=true); echo("Putting a hole with radius: ", hole_r , " at ", hole_dist_side, hole_dist_top); cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - h_margin; cv_in = [first_col, first_row, 0]; //Second row interface placement saw_out = [output_column, row_2, 0]; square_out = [output_column, row_1, 0]; square_out = [output_column, row_1, 0]; fm_in = [first_col, third_row, 0]; saw_out = [output_column, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, row_1, 0]; square_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; c_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - 9.5/2 - right_rib_thickness - tolerance; // rib + half a jack col_right = width_mm - 10 - center_adjust; center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [input_column, row_2, 0]; pwm_in = [first_col, fifth_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - thickness*2.2; footprint "SLIDE_POT_0547" (version 20221018) (generator pcbnew footprint "PinSocket_1x03_P2.54mm_Vertical" (version 20211014) (generator pcbnew main arrasta/arrasta_playbook_v0.9.txt 106 lines REP: repique CAX: caixa MSD: mid surdo (sometimes MS1, MS2, etc, if multiple measures or variations) BSD: back surdo (L for low, H for high R/L: Accented Note (right/left hand suggested)

r/l

Quieter, unaccented note

A trill, generally three very fast notes on updating the fireball for rev 2 beta by adding +5V, and both trigger/gate and CV routing updates led holes to PCB edge 9.12mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 37-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 62-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 9.9mm, distance of mounting holes 63.5mm, distance of mounting holes with circular drills, http://www.alps.com/prod/info/E/HTML/Encoder/Incremental/EC12E/EC12E1240405.html.

New Pull Request

Labels Milestones