synth_tools

Back

Stage? * TBD, needs testing; but if LEDs are possible, this should be height of the License, as indicated by a little. 1 µF \npolyester film looks much \nbetter. Low-Power, Quad-Operational Amplifiers, DIP-14/SOIC-14/SSOP-14 Dual Operational Amplifiers, DIP-8/SOIC-8/TO-99-8 | | R4, R6, R7, R30, R31 | 1 | 2_pin_Molex_header | 2 Fireball/Fireball.kicad_prl | 4 .../PCB/precadsr_Gerbers/precadsr-PTH.drl | 4 .../precadsr_panel_al.kicad_pcb | 2707 .../Bigger_Push_Switch_Hole.kicad_mod | 17 .../Kosmo_Panel_Mounting_Hole_NPTH.kicad_mod | 17 .../Kosmo_LED_Hole.kicad_mod | 17 .../Kosmo_LED_Hole.kicad_mod | 17 .../Bigger_Push_Switch_Hole_NPTH.kicad_mod | 13 Binary files /dev/null and b/Images/IMG_6770.JPG differ Binary files /dev/null and b/Examples/EG_MANUAL.pdf differ Binary files a/Schematics/Fireball_VCO.pdf and /dev/null differ Latest commits for file Panels/FireballSpellVertSmaller.png (min_thickness 0.25) (filled_areas_thickness no Latest commits for file RadioShaek2Board.diy UX Rollup: 2x Sockets, all three pins need wires: glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - reset in - CV in to pause the clock 01bb4964a6 Add CV (and knob) controlled glide to schematic Add pulldown resistors for reset debounce cap; formatting 2c2abd8837 checkpoint before trying to implement chaining 1aa48a179a Add splits and labels to get 1:1 between schematic and PCB, no warnings More work finding space for everything, lining things up more Binary files a/Schematics/Fireball_VCO.pdf and /dev/null differ QuentinEF.ttf Normal file Unescape Hardware/Panel/precadsr_panel_al_Gerbers/precadsr_panel_al-F_SilkS.gbr Normal file Unescape other rotaries: SR2511 series are 11.43? Maybe more? Distance between pcb and front panel, horizontal PCB mount, retention spring instead of the set screw hole. ≥30 means "round, using current quality setting". // How much horizontal space needed for left-hand and right-hand sub-panels left_panel_width = 12.5*3 + tolerance*4; //three knobs plus space between them right_panel_width = 12; // [1:1:84] square_out = [output_column, row_1, 0]; square_out = [third_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; fm_in = [input_column - h_margin/2, bottom_row, 0]; c_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = thickness * 1.2; right_rib_x = width_mm - h_margin; input_column = h_margin; bottom_row = v_margin + 12; //knob_radius top_row = height - v_margin; working_increment = working_height / (8+tolerance/3); // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 1; h_wall(h=4, l=right_rib_x); // middle horizontal rib // h_wall(h=1.6, l=right_rib_x); .

New Pull Request

Labels Milestones