Labels Milestones
BackRM 1.7mm, IIPAK, I2PAK, see http://pdf.datasheetcatalog.com/datasheet/irf/iris4011.pdf TO-262-5 Vertical RM 1.27mm staggered type-2 TO-220-5, Horizontal, RM 5.45mm, see https://www.fairchildsemi.com/package-drawings/TO/TO264A03.pdf TO-264-3 Horizontal RM 4.58mm IPAK TO-251-3, Vertical, RM 0.97mm, Multiwatt-9, staggered type-2 TO-220-9, Vertical, RM 2.54mm, staggered type-1 TO-220-11, Horizontal, RM 2.54mm, see https://toshiba.semicon-storage.com/us/product/mosfet/to-247-4l.html TO-247-2 Vertical RM 2.54mm staggered type-2 TO-220-5, Horizontal, RM 10.95mm, SOT-93, see https://www.vishay.com/docs/95214/fto218.pdf TO-218-3 Vertical RM 1.27mm MultiwattF-15 staggered type-2 TO-220-9 Horizontal RM 5.08mm TO-220F-3, Horizontal, RM 2.54mm, see https://www.njr.com/semicon/PDF/package/TO-220F-4_E.pdf TO-220F-4 Vertical RM 5.08mm TO-220-2, Vertical, RM 2.54mm, staggered type-2 TO-220-7, Vertical, RM 1.7mm, PentawattF-, MultiwattF-5 TO-220F-5 Vertical RM 2.54mm TO-220F-3, Vertical, RM 5.08mm, see https://www.diodes.com/assets/Package-Files/TO126.pdf TO-126-2 Horizontal RM 2.54mm TO-220F-3, Vertical, RM 5.45mm, , see https://toshiba.semicon-storage.com/ap-en/design-support/package/detail.TO-3P(N).html TO-3P-3 Horizontal RM 5.08mm TO-220F-3, Horizontal, RM 1.27mm, staggered type-1 TO-220-4, Horizontal, RM 2.286mm SIPAK Horizontal RM 0.97mm Multiwatt-9 staggered type-1 TO-220-4 Vertical RM 5.45mm TO-3P-3, Vertical, RM 2.54mm, IIPAK, I2PAK, see http://pdf.datasheetcatalog.com/datasheet/irf/iris4011.pdf TO-262-5 Horizontal RM 1.27mm MultiwattF-15 staggered type-2 TO-220F-9 Vertical RM 2.54mm TO-247-5, Vertical, RM 5.45mm, , see http://www.onsemi.com/pub/Collateral/340AC.PDF TO-3PB-3 Vertical RM 0.9mm staggered type-1 TO-220F-11, Vertical, RM 2.286mm Plastic near cylindrical package Sod-70 see: https://www.nxp.com/docs/en/data-sheet/KTY81_SER.pdf [StepUp generated footprint] SOT-227 / SOT-227B / ISOTOP, M4 mounting hole 2.2mm m2 din965 Mounting Hole 2.2mm, no annular, M2, ISO14580 mounting hole 2.7mm no annular m4 iso7380 Mounting Hole 2.7mm, M2.5, ISO7380 mounting hole position tweaks f6c7924538 Messing around with panel alignment before printing Add notes about UX component wiring 2x Sockets, all three pins need wires: - clk in - CV Range - Once/Cont 11 Toggle Switches, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - Glide attenuator (B10k) (join two left pins from below Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small for a single 0.15 mm² wires, reinforced insulation, conductor diameter 0.4mm, outer diameter 2mm, see http://www.produktinfo.conrad.com/datenblaetter/550000-574999/556444-da-01-de-LEITERPLATTENKL__PTSM_0_5__4_2_5_V_THR.pdf, script-generated with , script-generated with.
New Pull Request