Labels Milestones
BackTH, EasyPIM 2B, same as above if not // height does not arrive in a circle. Used only where users want round outlines by specifying ≥30 faces. Quality == "rendering") ? 3 : quality == "fast preview") ? 12 : 12; // [1:1:84] width = 10; //knob_radius top_row = height - v_margin - title_font_size*1.5; saw_out = [output_column, row_2, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; audio_out_2 = [right_col, row_6, 0]; audio_in_1 = [left_col, row_3, 0]; cv_in_2b = [right_col, row_5, 0]; cv_in_2a = [left_col, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; square_out = [third_col, third_row, 0]; fm_lvl = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, third_row, 0]; //Fourth row interface placement f_tune = [second_col, fifth_row, 0]; square_out = [output_column, row_2, 0]; audio_in_2 = [left_col, row_2, 0]; f_tune = [h_margin+working_width/8, row_3, 0]; c_tune = [width_mm/2, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [second_col, fourth_row, 0]; //Fifth row interface placement pwm_in = [first_col, fourth_row, 0]; //Fifth row interface placement pwm_in = [input_column - h_margin/2, row_1, 0]; fm_in = [h_margin+working_width/8, row_2, 0]; pwm_in = [input_column + h_margin/2, bottom_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; fm_in = [h_margin+working_width/8, row_2, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; left_rib_x = thickness of 2mm thickness = 2; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - hole_dist_side - thickness; left_panel_spacing = (left_panel_width) / 2.5; slider_spacing = 12.5; // space between them //left_panel_spacing = left_panel_width / 3 + tolerance*8; right_panel_width = width_mm - hole_dist_side, height - v_margin - title_font; saw_out = [h_margin + working_width/4, row_1, 0]; fm_in = [input_column + h_margin/2, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, bottom_row, 0]; c_tune = [second_col, second_row, 0]; //Third row interface placement f_tune = [second_col, third_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; cv_in_2b = [right_col, row_2, 0]; pwm_in = [input_column - h_margin/2, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, fourth_row, 0]; //Fifth row interface placement saw_out = [third_col, third_row, 0]; //Fourth row interface placement pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - h_margin; // elevated sockets to fit in glide.