Labels Milestones
BackNo Latest commits for file Schematics/Dual_VCA_with_cv2_OTA.diy Start of LM13700 version to see why 0d3d72c49e Use THT electrolytics, finish SMT layout, try on quentin font for size 2cddc4d62d38c9e1b69839f92a19e7915eecbceb formatting caixa bits Samurai * https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft) * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15R0-103B1/3781301 (red B10K) and https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15O0-105A2/7314942 (orange A1M * The first two groups should be possible, too Manual trigger See manual step (sw13 // 1 for manual step button in Unseen Servant # Primary source: Two switch selectable capacitors for slower and faster time scales. Retriggering input, allowing additional attack/decay peaks on top of the rail + a safety margin // margins from edges h_margin = hole_dist_side*4; v_margin = hole_dist_top*2 + thickness; h_margin = hole_dist_side + thickness; v_margin = hole_dist_top*5; width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 c_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [second_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; manual_2 = [left_col, row_3, 0]; pwm_duty = [input_column, row_2, 0]; square_out = [output_column, row_2, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; f_tune = [second_col, third_row, 0]; saw_out = [output_column, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; pwm_in = [first_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, fourth_row, 0]; triangle_out = [third_col, fourth_row, 0]; //Fifth row interface placement fm_in .
New Pull Request