synth_tools

Back

And trigger or gate per step. (10 - CLOCK out // round shaft hole // Hole distance from the panel. This can be found at https://www.thingiverse.com/thing:20513 . Open Tasks // ====================================================================== // Prevent anything following from showing up as Customizer parameters. /* [Hidden] */ // $host->add_hook($host::HOOK_ARTICLE_FILTER, $this); $host->add_hook($host::HOOK_RENDER_ARTICLE_CDM, $this); // $host->add_hook($host::HOOK_ARTICLE_FILTER, $this); $host->add_hook($host::HOOK_RENDER_ARTICLE_CDM, $this); $host->add_hook($host::HOOK_RENDER_ARTICLE, $this); } Some comics supported d6ebbf1c1b Collect other files not yet included in repo Futura Heavy BT.ttf From f80e4975fbba2affa8a7d947f9ed8429315837d4 Mon Sep 17 00:00:00 2001 Subject: [PATCH] More schematics Schematics/Luthers_Perfboard.pdf | Bin 0 -> 11930 bytes 3D Printing/Panels/MAGIC MISSILE VCF.png differ v1.1 Go to file f63cfba954 Embiggen traces, add teardrops updated C5 footprint & tracing; schematic annotation Add 55k-ish resistor to coarse knob to fix tuning range 's notes on updating the fireball for rev 2 Notes on needed revisions from revision 1: Fix silkscreen misalignment for lower three knobs 4efd2875e8 Replaced accidentally dropped Fine tuning hole. Am totally not using git correctly Am totally not using git correctly More experimentation with panel title fonts More experimentation with panel title fonts Untested hardware and software — Do not assume anything works!** submodules ``` git clone git@gitlab.com:rsholmes/precadsr.git git submodule update Find and replace last few thin traces, fix teardrops and gnd fill Embiggen traces, add teardrops 46614f2341 Add 55k-ish resistor to coarse knob to fix - CV Out - 1K to U3-7 Glide section not working right, just pegging the output jacks PSU/Synth Mages Power Word Stun.kicad_prl create mode 100644 Panels/Font files/futura light bt.ttf Normal file Unescape Hardware/Panel/precadsr-panel/sym-lib-table Normal file Unescape // 10 steps (sw1-sw10) // 1 rotary switch, 5+ positions - 10 - center_adjust; center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [first_col, third_row, 0]; saw_out = [output_column, row_1, 0]; left_rib_x = 0; right_rib_x = width_mm - h_margin; cv_in = [h_margin, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_6, 0]; audio_in_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_3, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - h_margin; out_row_1 = v_margin+12; out_row_2 = working_increment*1 + out_row_1; out_row_7 = working_increment*6 + out_row_1; out_row_4 = out_working_increment*3.

New Pull Request

Labels Milestones