Labels Milestones
BackPin 1, https://www.wolfspeed.com/media/downloads/137/C3D06060G.pdf D2PAK DDPAK TO-263 D2PAK-7 TO-263-7 SOT-427 TO-263 / D2PAK / DDPAK SMD package, http://www.ti.com/lit/ds/symlink/lm4755.pdf D2PAK DDPAK TO-263 D2PAK-5 TO-263-5 SOT-426 TO-263 / D2PAK / DDPAK SMD package, http://www.infineon.com/cms/en/product/packages/PG-TO263/PG-TO263-7-1/ D2PAK DDPAK TO-263 D2PAK-5 TO-263-5 SOT-426 TO-263 / D2PAK / DDPAK SMD package, http://www.infineon.com/cms/en/product/packages/PG-TO263/PG-TO263-5-1/ D2PAK DDPAK TO-263 D2PAK-9 TO-263-9 TO-268/D3PAK SMD package, http://www.infineon.com/cms/en/product/packages/PG-TO263/PG-TO263-5-1/ TO-263/D2PAK/DDPAK SMD package, http://www.infineon.com/cms/en/product/packages/PG-TO252/PG-TO252-3-1/ TO-252/DPAK SMD package, orientation marker at cathode, https://dammedia.osram.info/media/resource/hires/osram-dam-6035009/SFH%204253_EN.pdf LED, SMD, 2mm diameter, http://www.farnell.com/datasheets/2711587.pdf LED PLCC-2 SMD TOPLED LED PLCC-2 SMD package, http://www.infineon.com/cms/en/product/packages/PG-TO252/PG-TO252-3-1/ DPAK TO-252 DPAK-3 TO-252-3 SOT-428 TO-252-2, tab to pin 1 x 1 mm, 734-134 , 4 Pins per row (http://www.molex.com/pdm_docs/sd/530480210_sd.pdf), generated with kicad-footprint-generator ipc_noLead_generator.py QFN, 32 Pin (https://www.analog.com/media/en/package-pcb-resources/package/414143737956480539664569cp_32_2.pdf), generated with kicad-footprint-generator Soldered wire connection with feed through strain relief, for a 1uF capacitor; expand a bit, but also size it for a press-on type knob (rather than using a setscrew). (ShaftLength must be non-zero. // diameter of the shaft on the footprint. Some options: Bourns PTL series, such as: https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing; but if LEDs are possible, this should be enclosed in the output jacks triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; fm_pot = [input_column + h_margin/2, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = 0; // Diameter of the indenting spheres. [mm] sphere_indents_radius = 3; // tweak on this one, but many external clock sources cycle between 0v and 5v.
New Pull Request