Labels Milestones
BackFAB, Suitable for order numbers 0031.3551 and 0031.3558 (https://www.schurter.com/bundles/snceschurter/epim/_ProdPool_/newDS/en/typ_FAB.pdf Fuseholder 5x20mm closed horizontal Shock-Safe Fuseholder, 5 x 20 mm fuses; 250V; 10A (http://www.cooperindustries.com/content/dam/public/bussmann/Electronics/Resources/product-datasheets/bus-elx-ds-4426-h15.pdf fuse holder vertical 5x20mm 5 mm | | R20, R22 | 3 | 4.7k | Resistor | | | | | Tayda | A-1955 | | S2 | 1 | Conn_01x02 | SIP socket, 2.54 mm, 1x10 Pin header, 2.54 mm, 1x4 Pin header, 2.54 mm, 1x7 | | R31 | 1 uF | Polarized capacitor | | | U3 | 1 uF tantalum\nYuSynth 1, 10 µF tantalum.\nMFOS 1, 1+15 µF electrolytic.\n1 µF tanty to try two more (same type, from the other was worse. Images/IMG_6753.JPG Normal file Unescape // testing futura vs quentincaps in F6 rendering label_font_size = 5; //knob_radius top_row = height - v_margin - title_font_size*2; working_width = width_mm - hole_dist_side - thickness; left_panel_spacing = (left_panel_width) / 2.5; slider_spacing = 12.5; // space between two resistors, and updated with more panel layout ideas left_rib_x = thickness + 6 + tolerance; // rib + half a jack col_right = width_mm - thickness; // column from edge plus hole radius // mounting holes - these gaps reduce heat conduction during soldering - ground planes are copper fill applied everywhere there isn't a trace already use spokes where ground planes connect to the PSU?) UI: 2 5mm LEDs b1fcba1e78 Bring in diylc and openscad design 77735c00cc3285131373f5cfc61b82eab5963d12 Update README.md 8be0bd80e05e7fe62720d7fda27423a4c75b90a3 Update README.md Don't put R8 so close to R26 -- D36/R47 too close Testing before powering up: Clock In - Pause CV In - U1-13 (can get at from top when assembled - Stop Switch - 10 - center_adjust; // build up seven rows; middle one unused row_2 = working_increment*1 + row_1; row_3 = row_2 + vertical_space/7; row_6 = row_5 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_5 = row_4 + vertical_space/7; cv_in_1a = [left_col, row_7, 0]; cv_in_1b = [right_col, row_3, 0]; c_tune = [width_mm/2, top_row, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - thickness*2; From 88bf85725f2c856b6f99f99568e61e08e1060d3b Mon Sep 17 00:00:00 2001 Subject: [PATCH] Adding SynthMages footprint library Examples: https://www.youtube.com/watch?v=-2No01KfY4k https://youtu.be/Jeh8iTI6gMc?t=96 https://youtu.be/frLXzG9-W3Q?t=712 (until 15:50 Key: REP: repique MSD: mid surdo BSD: back surdo (L for low, H for high)
- Connector, 505405-0970 (http://www.molex.com/pdm_docs/sd/5054050270_sd.pdf), generated with.
- Will automatically terminate your rights under this.