synth_tools

Back

Tighten up schematic, fit letter instead of latch, https://www.neutrik.com/en/product/nc3fav1-0 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, vertical PCB mount, additional ground contacts, https://www.neutrik.com/en/product/nc3fbh1-e B Series, 3 pole female receptacle, grounding: without ground/shell contact, horizontal PCB mount, https://www.neutrik.com/en/product/ncj6fa-h Combo A series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, switched, with chrome ferrule and straight PCB pins, https://www.neutrik.com/en/product/nmj4hhd2 M Series, 6.35mm (1/4in) mono jack, switched, fully threaded nose, https://www.neutrik.com/en/product/nrj6hh-au Slim Jacks, 6.35mm (1/4in) jack receptacle, vertical pcb mount, replaces NL8MD-V, https://www.neutrik.com/en/product/nl8mdxx-v 4 contacts, 3.5mm audio plug, https://www.cuidevices.com/product/resource/pdf/sp-3541.pdf DC Barrel Jack 2mm or 2.5mm center pin, https://www.kycon.com/Pub_Eng_Draw/KLDX-0202-AC%20&%20BC.pdf power jack works physically for male connector from wall wart. - Consider adding a switch to disable clock (pause). SPST switch to disable clock (pause). SPST switch per step, to indicate direction? Pointer2 = 1; // [0:No, 1:Yes] ////////////////////////// ////////////////////////// RingThickness = 5*1; DivotDepth = 1.5*1; MarkingWidth = 1.5*1; DistanceBetweenKnurls = 3*1; TimerKnobConst = 1.8*1; ////////////////////////// KnobMinorRadius = KnobDiameter/2 * (1 - TaperPercentage/100); KnobRadius = KnobMinorRadius + (KnobMajorRadius-KnobMinorRadius)/2; Divot=CapType; TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) + pow(KnobMajorRadius-KnobMinorRadius,2)))) - 90; DivotRadius = KnobMinorRadius*.4; // Primary knob cylinder for (i=[0 : Knurls-1] rotate([0, 0, 180] // Left side: meta-step controls } module make_surface(filename, h) { for (a = [1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16] if (h < four_hole_threshold) { if (two_holes_type == "mirror") { module mounting_hole_m3(h=thickness, flange=8, style="nut"){ cube([flange, flange, h], center=true); if (RingWidth>0 cylinder(r1=KnobMajorRadius + RingWidth, r2=KnobMinorRadius, h=RingThickness, $fn=50, center=true); if (RingWidth>0 cylinder(r1=KnobMajorRadius + RingWidth, r2=KnobMinorRadius, h=RingThickness, $fn=50, center=true); if (RingMarkings>0 for (i=[0 : Knurls-1] rotate([0, 0, i * (360/Knurls)] rotate([0, TaperAngle, 0]) rotate([0, 0, 90]) // To align a face with the Work.

New Pull Request

Labels Milestones