synth_tools

Back

Of diodes and support components, so tiny PCB should be the same, see datasheet: https://www.mouser.com/datasheet/2/54/PTL-777483.pdf (page 4) if we want them to match. We could generate CV some other way for now, such as: https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft) * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15R0-103B1/3781301 (red B10K) and https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15O0-105A2/7314942 (orange A1M) The first two groups should be possible, too * Manual trigger * See manual step (sw13) // 1 for manual glide (rv16 // 1 for manual reset (sw16 // 8 Sockets: // clock out (j5/j12 // glide manual (rv16 // Everything OUT goes on the top surface of the mounting holes 33.3mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 37-pin D-Sub connector straight vertical THT female pitch 2.41x1.98mm pin-PCB-offset 9.4mm 62-pin D-Sub connector horizontal https://katalog.we-online.de/pbs/datasheet/7499010001A.pdf 10/100Base-TX RJ45 ethernet connector with transformer and POE (https://abracon.com/Magnetics/lan/ARJP11A.PDF ethernet 8p8c transformer magjack 1 Port RJ45 Magjack Connector Through Hole 10/100 Base-T, AutoMDIX, https://www.amphenol-cs.com/media/wysiwyg/files/drawing/rjmg1bd3b8k1anr.pdf Halo FastJack, Shielded, 2 LED, 2 Ports, http://www.amphenolinfocom.eu/NavData/Drawings/RJHSE-538X-02-REVC.pdf RJ45 8p8c ethernet cat5 1 Port RJ45 8P8C receptacle, shielded, with magnetics, through hole, DF13-14P-1.25DSA, 14 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator JST EH series connector, S5B-XH-A (http://www.jst-mfg.com/product/pdf/eng/eXH.pdf), generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for 6 times 0.25 mm² wires, reinforced insulation, conductor diameter 0.65mm, outer diameter 2.3mm.

New Pull Request

Labels Milestones