Labels Milestones
BackCommits » 2bd01a1ff2 Add schematic, start on PCB with on-board components Added hard sync to schematic, laid out PCB with exploratory 8hp layout Add VCA shaek layout These branches are equal. There is a ceramic 104 power cap like C5, C6, C8, C9, C11, C12. - C10, C14 too small for a single 1.5 mm² wires, reinforced insulation, conductor diameter 2.4mm, outer diameter 3.5mm, size 18.2x7mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_317011_RT11LxxHGLU_OFF-022798U.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00076, 11 pins, pitch 5.08mm, size 50.8x10.6mm^2, drill diamater 1.3mm, pad diameter 2.1mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00045_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block WAGO 804-305 45Degree pitch 5mm Varistor, diameter 12mm, width 6.7mm, pitch 7.5mm size 24.8x14mm^2 drill 1.15mm pad 3mm Terminal Block WAGO 804-302 45Degree pitch 5mm size 25x10.5mm^2 drill 1.4mm pad 2.6mm Terminal Block WAGO 236-424, 45Degree (cable under 45degree), 1 pins, pitch 7.5mm, size 62.3x14mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_317011_RT11LxxHGLU_OFF-022798U.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MKDS-1,5-15, 15 pins, pitch 5mm, size 10x7.6mm^2, drill diamater 1.2mm, pad diameter 2.2mm, see http://www.mouser.com/ds/2/324/ItemDetail_1725672-916605.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00298, 2 pins, diameter 5.0mm z-position of LED center 3.0mm 2 pins LED_Rectangular, Rectangular, Rectangular size 4.0x2.8mm^2 diameter 2.0mm, 2 pins, pitch 5.08mm, hole diameter 0.7mm, length 6.5mm, width 1.8mm solder Pin_ with flat fork solder Pin_ with flat with fork, hole diameter 1.4mm wire loop as test point, loop diameter2.6mm, hole diameter 0.7mm THT pad as test Point, square 1.5mm side length, hole diameter 1.2mm (loose fit), length 10.0mm solder Pin_ with flat with hole, hole diameter 1.0mm wire loop wire loop with bead as test point, loop diameter2.6mm, hole diameter 1.5mm (loose fit), length 10.0mm solder Pin_ with flat with fork, hole diameter 1.85mm wire loop with bead as test point, pitch 7.62mm, hole diameter 1.3mm, length 11.3mm, width 3.0mm Capacitor C, Disc series, Radial, pin pitch=4.57mm, , length*width=13.97*6.35mm^2, Pulse, A, http://datasheet.octopart.com/PE-92112KNL-Pulse-datasheet-17853305.pdf L_Toroid Vertical series Radial pin pitch 85mm length 80mm diameter 23.0mm Electrolytic Capacitor CP, Radial series, Radial, pin pitch=5.00mm, , diameter=10mm, Electrolytic Capacitor CP, Radial series, Radial, pin pitch=27.18mm, .
New Pull Request