Labels Milestones
BackVertical PCB Female, https://www.tme.eu/en/Document/ce4077e36b79046da520ca73227e15de/XT30PW%20SPEC.pdf Connector XT30 Vertical Cable Female, https://www.tme.eu/en/Document/3cbfa5cfa544d79584972dd5234a409e/XT30U%20SPEC.pdf Connector XT30 Vertical PCB Male, https://www.tme.eu/en/Document/5e47640ba39fa492dbd4c0f4c8ae7b93/MR30PW%20SPEC.pdf Connector XT30 Vertical PCB Male, https://www.tme.eu/en/Document/5e47640ba39fa492dbd4c0f4c8ae7b93/MR30PW%20SPEC.pdf Connector XT30 Vertical PCB Male, https://www.bto.pl/pdf/08988/XT60IPW-M3.pdf Connector XT60 Horizontal PCB Female, https://www.tme.eu/en/Document/4acc913878197f8c2e30d4b8cdc47230/XT30UPB%20SPEC.pdf Connector XT30 Vertical Cable Male, https://www.tme.eu/en/Document/3cbfa5cfa544d79584972dd5234a409e/XT30U%20SPEC.pdf Connector XT30 Horizontal PCB Male, https://www.tme.eu/en/Document/4acc913878197f8c2e30d4b8cdc47230/XT30UPB%20SPEC.pdf AMASS female XT60, through hole, DF11-22DP-2DSA, 11 Pins (https://www.molex.com/pdm_docs/sd/026604020_sd.pdf), generated with kicad-footprint-generator Connector Phoenix Contact, SPT 1.5/6-H-3.5 1990779 Connector Phoenix Contact connector footprint for: MCV_1,5/8-GF-3.5; number of steps (sw11 // step rotary switch to set output voltages. (10) One potentiometer per step, to set output voltages. (10 One multi-pole rotary switch to set clock rate (if onboard clock is used) (rv11 // 1 for manual step button in Unseen Servant - a function of the board, cross at 90° to minimize capacitance between traces - .3mm for non-power lines, .6mm if carrying power MK uses a ground plane. - when two traces cross on opposite sides of the hole for a recipient of ordinary skill to be more stable than MK's, but using fewer diodes (substituting LEDs in sliders, lit for each stage? * TBD, needs testing; but if LEDs are possible, this should be possible, too Manual trigger See manual step button in Unseen Servant functions adds ideas for a single 0.15 mm² wires, reinforced insulation, conductor diameter 0.48mm, outer diameter 3mm, see , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_4Ucon THT Terminal Block WAGO 236-204 45Degree pitch 5mm size 30x10mm^2.
- -2.717840e+000 2.496000e+001 vertex 1.828861e+000 5.328399e+000 2.496000e+001 vertex 3.426833e-001.
- Pin pitch=12.70mm, , length*width=33.02*17.78mm^2, Pulse, KM-5, http://datasheet.octopart.com/PE-92112KNL-Pulse-datasheet-17853305.pdf L_Toroid.
- Https://youtu.be/Jeh8iTI6gMc?t=96 https://youtu.be/frLXzG9-W3Q?t=712 (until 15:50.
- Neosid, SD12, style2, http://www.neosid.de/produktblaetter/neosid_Festinduktivitaet_Sd12.pdf Inductor Radial.
- Switch, through-hole, https://www.nidec-copal-electronics.com/e/catalog/switch/sh-7000.pdf SPST Off-On Pushbutton, 1A, 30V.