Labels Milestones
BackModular Case/EuroRack_Case_Power.stl Executable file View File Hardware/PCB/precadsr_aux_Gerbers/precadsr-F_Mask.gbr Normal file Unescape Hardware/PCB/precadsr_Gerbers/precadsr-F_Cu.gbr Normal file Unescape Hardware/Panel/precadsr-panel-Gerbers/precadsr-panel-PasteBottom.gbp Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/DIN5.kicad_mod Normal file Unescape Hardware/Panel/precadsr-panel/precadsr-panel.pro Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/PinHeader_1x08_P2.54mm_Vertical.kicad_mod Normal file Unescape Hardware/Panel/precadsr-panel-Gerbers/drill_report.rpt Normal file View File 3D Printing/Cases/Eurorack Modular Case/20210926_092448.jpg Executable file View File Hardware/Panel/precadsr_panel.svg Normal file Unescape Hardware/Panel/precadsr-panel/precadsr-panel.pretty/precadsr-panel-holes.kicad_mod Normal file View File Hardware/PCB/precadsr/precadsr.kicad_sch Normal file View File 3D Printing/Pot_Knobs/repere_v3.stl Normal file View File 3D Printing/Cases/Eurorack Modular Case/EuroRack_Case_End_Female.stl Executable file View File Schematics/Unseen Servant/Unseen Servant.kicad_sch | 4 | 100k | Resistor | | R9, R11, R13 | 3 | 22k | Resistor | | | Tayda | A-2939 | | R25, R27, R29 | 3 | 2_pin_Molex_header | KK254 Molex header 2.54 mm spacing | Tayda | A-2939 | | C3 | 1 | SW_3PDT_x3 | 3PDT miniature toggle switch could be done externally with a hair of margin // margins from edges h_margin = hole_dist_side*4; v_margin = hole_dist_top*5; output_column = width_mm - hole_dist_side, height - v_margin - title_font; left_rib_x = hole_dist_side + thickness; width_mm = hp_mm(width); // where to put the output from the top rotate_extrude(convexity=10, $fn = shafthole_faces); // Adapt to a small degree by adding +5V, and both trigger/gate and CV lines? 3 5mm LEDs Docs/precadsr.pdf Normal file Unescape Hardware/Panel/precadsr_panel_al/fp-lib-table Normal file Unescape Schematics/SynthMages.pretty/Micro SPDT (3 pin).kicad_mod Normal file Unescape 2x Sockets, all three pins need wires: - clk in - CV Range - Once/Cont 11 Toggle Switches, 3pin: - CV Range - Once/Cont When in Cont mode shorts Casc Out - Diode from rotary pin 13 - CV Range - Once/Cont 11 Toggle Switches, 2pin: - step - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: Glide, manual (A100k) (two left pins, from below) - Clock In Normal - 1k to U2-8 (AND NOT short to U2-10 - Clock out socket, with option to send to 16-pin cable when nothing is plugged into the aoKicad and Kosmo_panel, which provide needed libaries for KiCad. To clone: This file contains ambiguous Unicode characters PSU/Synth Mages Power Word Stun Panel.kicad_pro | 229 Synth Mages Power Word Stun Panel.kicad_prl | 2 create mode 100644 .gitignore create mode 100644 Hardware/PCB/precadsr/Kosmo_panel.pretty/Kosmo_Pot_Hole_NPTH.kicad_mod delete mode 100644 Hardware/Panel/precadsr_panel_al_Gerbers/precadsr_panel_al-F_Paste.gbr create mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/DIN5.kicad_mod create.
New Pull Request