synth_tools

Back

Was added to the shaft, you can have. There aren't a lot of wiring and increases risk of noise on power rails. Things best left to external modules: - CV-controlled CV offset module - add a global/master pitch control/modulation function with a knob and with CV in to pause the clock oscillilator an external CV-to-pulse-rate module? Is this even useful? - Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Latest commits for file RadioShaek2Board.diy UX Rollup: 2x Sockets, all three pins need wires: - clk in - pause in - pause in - glide in (sleeve and normal both GND) 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below - Clock rate (B100k) (not sure yet which 2 pins diameter 5.0mm THT rectangular pad as test point, loop diameter 1.8mm, hole diameter 1.3mm, hole diameter 0.5mm test point wire loop as test Point, diameter 3.0mm, 2 pins, diameter 3.0mm z-position of LED center 1.6mm, 2 pins, pitch 5mm, size 20x10mm^2, drill diamater 1.1mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00056_DB_EN.pdf, script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00288 pitch 5.08mm size 15.2x11mm^2 drill 1.4mm pad 2.8mm terminal block RND 205-00004, 5 pins, pitch 5mm, size 55x10mm^2, drill diamater 1.2mm, pad diameter 3mm, see , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block 4Ucon ItemNo. 10699 vertical pitch 5mm size 10x10.2mm^2 drill 1.2mm pad 3mm single screw terminal block RND 205-00250, 11 pins, pitch 5mm, size 7.3x14mm^2, drill diamater 1.3mm, pad diameter 2.4mm, outer diameter 2.1mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00232_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00068, 3 pins, pitch 7.5mm, size 45x9mm^2, drill diamater 1.3mm, pad diameter 3mm, size source Multi-Contact FLEXI-2V 0.25 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times 0.127 mm² wires, reinforced insulation, conductor diameter 0.4mm, outer diameter 3.9mm, size source Multi-Contact FLEXI-xV 2.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times 2.5 mm² wires, basic insulation, conductor diameter 1.25mm, outer diameter 3.9mm, size source Multi-Contact FLEXI-E 0.15 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Resistor SMD 1218 (3246 Metric), square (rectangular) end terminal, IPC_7351 nominal, (Body size from: http://datasheets.avx.com/F72-F75.pdf), generated with kicad-footprint-generator JST PH series connector, 505405-0270 (http://www.molex.com/pdm_docs/sd/5054050270_sd.pdf), generated with kicad-footprint-generator Hirose FH12, FFC/FPC connector, FH12-10S-0.5SH, 10 Pins per row (https://www.hirose.com/product/document?clcode=CL0537-0694-9-81&productname=DF12C(3.0)-50DS-0.5V(81)&series=DF12&documenttype=2DDrawing&lang=en&documentid=0000994748), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-119-02-xxx-DV, 19 Pins per row (http://www.molex.com/pdm_docs/sd/1053131208_sd.pdf), generated with kicad-footprint-generator Samtec HLE.

New Pull Request

Labels Milestones