Labels Milestones
Back5KP series Axial Horizontal pin pitch 5.00mm length 7.5mm width 5.0mm Capacitor C, Disc series, Radial, pin pitch=8.40mm, , length*width=21.6*9.1mm^2, Bourns, 5700, http://www.bourns.com/docs/Product-Datasheets/5700_series.pdf L_Toroid Vertical series Radial pin pitch 7.62*12.70mm^2 length 16.13mm width 16.13mm Pulse LP-44 Self Ferrite 14 - 18 L_Toroid, Horizontal series, Radial, pin pitch=8.38mm, , length*width=21.59*8.38mm^2, Pulse, G, http://datasheet.octopart.com/PE-92112KNL-Pulse-datasheet-17853305.pdf L_Toroid Vertical series Radial pin pitch 5.08mm size 40.6x10.6mm^2 drill 1.3mm pad 2.5mm terminal block Metz Connect 360425, block size 9x7.3mm^2, drill diamater 1.3mm, pad diameter 2.4mm, outer diameter 3.9mm, size source Multi-Contact FLEXI-xV 2.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for 4 times 0.25 mm² wires, basic insulation, conductor diameter 0.48mm, outer diameter 1.5mm, size source Multi-Contact FLEXI-xV 2.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, * Knurl polyhedron width, * Knurl polyhedron width, * Knurl polyhedron height, * Knurl polyhedron height, * Knurled surface smoothing amount ); * If you want a D-shaped shafthole cross-section. 0 to keep labels all the way through then set this value to zero. ShaftLength = 0; right_rib_x = width_mm - h_margin; working_height = height - v_margin - title_font; saw_out = [h_margin + working_width/4, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; saw_out = [output_column, row_2, 0]; fm_lvl = [second_col, third_row, 0]; saw_out = [output_column, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; right_rib_x = width_mm - 10 - center_adjust; // build up seven rows; middle one unused row_7 = row_6 + vertical_space/7; row_5 = row_4 + vertical_space/7; row_4 = row_3 + vertical_space/7; row_3 = working_increment*2 + row_1; row_3 = row_2 + vertical_space/7; row_6 = row_5 + vertical_space/7; cv_in_1a = [left_col, row_1, 0]; saw_out = [output_column, row_2, 0]; cv_2b_atten = [right_col, row_6, 0]; audio_in_1 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_3, 0]; cv_in_2b = [right_col, row_6, 0]; audio_in_1 = [left_col, row_7, 0]; manual_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_7, 0]; manual_1 = [left_col, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - 10 - center_adjust; // build up seven rows; middle one unused row_2 = row_1 + v_margin + 12; //knob_radius top_row = height - v_margin - title_font_size*2; saw_out = [output_column, row_2, 0]; f_tune = [second_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0.
New Pull Request