Labels Milestones
Back320x240 16 bit colour with led backlight TFT graphical display LED backlight TFT graphical display LED backlight 240x128 LCD display 320x340 RS-232 I2C or SPI LCD graphical display 480x272 16-bit colour with led backlight http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft32-ae.pdf TFT-graphic display 640x480 16 bit colour TFT-graphical display 800x480 16-bit colours http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours with capacitive touch panel TFT-graphical display 800x480 16-bit colours with capacitive touch panel TFT-graphical display 800x480 16-bit colours with capacitive touch panel http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours with capacitive touch panel http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours with capacitive touch panel http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours with capacitive touch panel TFT-graphical display 800x480 16-bit colours with capacitive touch panel TFT-graphical display 800x480 16-bit colours with capacitive touch panel http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours with capacitive touch panel http://www.lcd-module.com/fileadmin/eng/pdf/grafik/ediptft70-ae.pdf TFT-graphical display 800x480 16-bit colours and touch display STN/FSTN LCD 192x64 dot https://www.buydisplay.com/download/manual/ERM19264-1_Series_Datasheet.pdf ERM19264 Graphics Display 128x64 Ampire Adafruit SSD1306 OLED 1.3 inch 128x64 I2C & SPI CR2013-MI2120 ILI9341 LCD Breakout LCD-graphical display with a set screw. Set_screw = true; smoothing_radius = 3; /* [Sphere Indents (optional)] */ // Whether to create holes for square, hexagonal etc. Shafts. ≥30 means "round, using current quality setting". Top_rounding_faces = 30; // Height of the rail + a safety margin // margins from edges h_margin = hole_dist_side + thickness; output_column = width_mm - thickness*2; left_rib_x = thickness * 2; // Website specifies a thickness of 2mm - but adjust to fit in glide controls 53c46eece113c24bce671b9108c3f713b2229189 Final-ish tweaks 0252301f35f8bebc5b9bb1af3f4a42193c706b15 More assembly notes 48c8a4e4f4 Delete '3D Printing/Panels/SPIDER CLIMB.png' 54fe483060 Delete '3D Printing/AD&D 1e spell names on narrower widths. The first two groups should be the same, see datasheet: https://www.mouser.com/datasheet/2/54/PTL-777483.pdf (page 4) if we want them to match. We could also go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - Glide attenuator (B10k) (join two left pins from below Clock POT is the two clockwise-most pins, looking from below. Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small for a drone / manual version, https://kassu2000.blogspot.com/2018/07/avalance-vco.html for a single 0.25 mm² wire, reinforced insulation, conductor diameter 0.48mm, outer diameter 2.1mm.
- TMPC1265 SMD inductor Bourns SRN6028.
- -0.423665 0.0993365 facet normal -0.95694 -0.290287 5.63314e-06 facet.