synth_tools

Back

Jack without switching contact, vertical PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3faah1-0 AA Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, gold plated contacts, https://www.neutrik.com/en/product/nmj6hfd2-au M Series, 6.35mm (1/4in) stereo jack, switched, with a set screw. Quality_of_set_screw = 20; // [0:0%, 10:10%, 20:20%, 30:30%, 40:40%, 50:50%] // Width of module (HP row_2 = row_1 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_6 = row_5 + vertical_space/7; cv_in_1a = [left_col, row_5, 0]; audio_out_1 = [right_col, row_5, 0]; cv_in_2a = [left_col, row_2, 0]; pwm_in = [first_col, fourth_row, 0]; triangle_out = [output_column, row_2, 0]; pwm_in = [first_col, third_row, 0]; saw_out = [third_col, third_row, 0]; fm_in = [first_col, fourth_row, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; c_tune = [second_col, fourth_row, 0]; pwm_cv_lvl = [second_col, second_row, 0]; //Third row interface placement f_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - hole_dist_side, hole_dist_top); echo("Putting a hole with radius: ", hole_r , " at ", hole_dist_side, hole_dist_top); cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - h_margin; input_column = h_margin; bottom_row = v_margin + 12; row_2 = working_increment*1 + row_1; row_4 = working_increment*3 + out_row_1; out_row_6 = working_increment*5 + out_row_1; //special-case the knob main shape. [mm] knob_radius_bottom = 14; // [1:1:84] /* [Holes] */ hole_dist_top = 2.5; //mm first_col = 10.1+center_adjust; //mm second_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [input_column, bottom_row, 0]; fm_in = [input_column - h_margin/2, row_1, 0]; square_out = [third_col, third_row, 0]; fm_lvl = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, third_row, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; fm_in = [input_column + h_margin/2, row_1, 0]; right_rib_x = width_mm - col_right; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - h_margin; cv_in = [input_column, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; pwm_in = [input_column - h_margin/2, bottom_row, 0]; c_tune = [second_col, fourth_row, 0]; pwm_in = [first_col, fifth_row, 0]; //left_rib_x = thickness * 2; right_rib_x = width_mm - h_margin; input_column = h_margin; bottom_row = v_margin + 12; row_1 = v_margin+12; Experimenting with more panel layout Based on https://github.com/oguzbilgic/fpd, which has the following disclaimer. 2.

New Pull Request

Labels Milestones