synth_tools

Back

The LEDs //outline of whole PCB? // cube([137.5, 97, 1], center=true); working_increment = working_height / 5; out_row_2 = working_increment*1 + row_1; row_4 = row_3 + vertical_space/7; row_7 = row_6 + vertical_space/7; cv_in_1a = [left_col, row_7, 0]; manual_1 = [left_col, row_3, 0]; manual_2 = [left_col, row_7, 0]; cv_in_1b = [right_col, row_5, 0]; cv_in_2a = [left_col, row_2, 0]; fm_in = [first_col, third_row, 0]; fm_lvl = [second_col, fourth_row, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness * 1; right_rib_x = width_mm - 9.5/2 - right_rib_thickness - tolerance; // left_rib_x = thickness * 2; right_rib_x = width_mm - col_right; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - hole_dist_side, height - v_margin - title_font_size*2; working_width = width_mm - 10 - center_adjust; center_col = width_mm/2; row_1 = vertical_space/7; row_2 = row_1 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_5 = row_4 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_4 = row_3 + vertical_space/7; row_6 = row_5 + vertical_space/7; row_3 = row_2 + vertical_space/7; cv_in_1a = [left_col, row_3, 0]; pwm_duty = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness + 6 + tolerance; // rib + half a jack col_right = width_mm - hole_dist_side, height - rail_clearance - thickness*2 - 16.5/2; // 16.5 is the main hole format cylinder( h=clf_partHeight, r=clf_shaft_diameter/2 ); // the first layer will be given a distinguishing version number. The Program (including its Contributions) on an "as is" * * Contributor, or anyone who receives the Program is covered by two beats Paul Simon https://www.youtube.com/watch?v=A3o30YJiWsc (also featuring drum tricks) https://www.youtube.com/watch?v=frLXzG9-W3Q (until the callout around 2:30 Duro https://youtu.be/v9A9n-kMjz0?t=209 (until ~4:30 New: A different Timbalada https://youtu.be/frLXzG9-W3Q?t=955 From 8e97a73397a03125f3bf5b9aa13372a2d7319ad0 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Add notes about UX component wiring 2x Sockets, all three pins need wires: - clk in - pause in - pause in - glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - reset in - glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - reset in - RESET / CASCADE in - glide in (sleeve and normal both GND Glide attenuator (B10k) (join two left pins from below Clock rate goes down when resistance goes up, opposite to expectation. Glide fix glide fix - Errant.

New Pull Request

Labels Milestones