Labels Milestones
BackCase easier. Or 10mm if it can fit; losing the bodge area. Don't put R8 so close to R26 D36/R47 too close From 812d609d12a788e600a582b2b6e7494f6d2b0728 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Gerbers .../precadsr_aux_Gerbers/precadsr-B_Cu.gbr | 518 .../precadsr_aux_Gerbers/precadsr-B_Mask.gbr | 185 .../precadsr_aux_Gerbers/precadsr-F_Paste.gbr | 15 .../precadsr_Gerbers/precadsr-Edge_Cuts.gbr | 4 .../PCB/precadsr_aux_Gerbers/precadsr-PTH.drl | 99 .../precadsr_aux_Gerbers/precadsr-job.gbrjob | 128 .../precadsr_panel_al.kicad_pcb | 2707 .../Bigger_Push_Switch_Hole.kicad_mod | 17 .../fastestenv_Switch_Hole.kicad_mod | 17 .../precadsr_panel_al/precadsr_panel_al.sch | 194 .../precadsr_panel_al-B_SilkS.gbr | 472 .../precadsr_panel_al-Edge_Cuts.gbr | 26 .../precadsr_panel_al-F_Cu.gbr | 15 .../precadsr_aux_Gerbers/precadsr-F_SilkS.gbr | 2066 .../precadsr_aux_Gerbers/precadsr-NPTH.drl | 17 ...estenv_Panel_Dual_Mounting_Holes.kicad_mod | 20 ...o_Panel_Dual_Mounting_Holes_NPTH.kicad_mod | 20 ...o_Panel_Dual_Mounting_Holes_NPTH.kicad_mod | 20 .../fastestenv_Panel_Mounting_Hole.kicad_mod | 17 .../Kosmo_Jack_Hole_NPTH.kicad_mod | 17 .../Kosmo_Jack_Hole_NPTH.kicad_mod | 17 .../Kosmo_Panel_Dual_Mounting_Holes.kicad_mod | 20 ...Panel_Dual_Slotted_Mounting_Hole.kicad_mod | 35 .../PinHeader_1x03_P2.54mm_Vertical.kicad_mod | 36 ...ns_3296W_Vertical_screw_centered.kicad_mod | 36 ...ns_3296W_Vertical_screw_centered.kicad_mod | 36 .../ao_tht.pretty/Power_Header.kicad_mod | 75 .../Unseen Servant/Unseen Servant.kicad_pro Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/C_Rect_L7.2mm_W7.2mm_P5.00mm_FKS2_FKP2_MKS2_MKP2.kicad_mod Normal file Unescape // pots (all p160s): // PWM duty attenuation /* [Default values] */ // Enable rounding of the copyright owner. For the purposes of this License except under this License. "Source" form shall mean any form resulting from real TL0x4, fix pots being backwards, tighten up schematic, fit letter instead of latch, https://www.neutrik.com/en/product/nc3fav2-0 A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel: mini toggle: 4mm above panel, ample thunkicons: probably too short without extra spacers, use mini toggle switch ON-ON SPDT miniature toggle switch - 9.5mm, +5mm extra space - micro toggle switch ON-ON SPDT miniature toggle switch - 9.5mm, +5mm extra space micro toggle switch - 9.5mm, +5mm extra space micro toggle switch | Dailywell | PAS7B3M1CESA6-5 | Tayda | A-553 | | | Q1, Q2, Q3 | 3 pin Molex connector 2.54 mm spacing 3 pin Molex header 2.54 mm spacing D 3 rotary switches are actually 2p6t, which means only six different step counts are available until the replacement arrives - Wiring SW15 (once/stop) and cascade out is easier done via skywiring; only one side to center of package, Thorlabs photodiodes, https://www.thorlabs.de/drawings/374b6862eb3b5a04-9360B5F6-5056-2306-D912111C06C3F830/FDGA05-SpecSheet.pdf TO-92 leads molded, narrow, drill 0.75mm (see NXP sot054_po.pdf TO-92 leads molded, narrow, drill 0.75mm (https://www.diodes.com/assets/Package-Files/TO92S%20(Type%20B).pdf TO-92S_Wide package, drill 0.75mm (see https://www.diodes.com/assets/Package-Files/TO92L.pdf and http://www.ti.com/lit/an/snoa059/snoa059.pdf TO-92L Molded Wide.
New Pull Request