Labels Milestones
Back// h_wall(h=4, l=right_rib_x); // middle horizontal rib h_wall(h=4, l=right_rib_x); } module make_surface(filename, h) { for (a = [1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16]) linear_extrude(height=a/h, convexity=10) projection(cut = true) surface(filename, center=true); } // Joy of Tech elseif (strpos($article['link'], 'dilbert.com/strip/') !== FALSE) { $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, "//div[@class='comic-wrap']//img[@class='comic']", $article); list($html, $content_type) = $this->get_content($link); $xpath = new DOMDocument(); elseif (strpos($article['link'], 'www.geekculture.com/joyoftech/') !== FALSE) { elseif (strpos($article['link'], 'girlswithslingshots.com/comic/') !== FALSE) { $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, "//div[@id='content']/img", $article); elseif (strpos($article["link"], "poorlydrawnlines.com/comic/") !== FALSE || strpos($article['content'], 'thedoghousediaries.com/dhdcomics/') !== FALSE) { $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, "//div[@id='comic']/img", $article); elseif (strpos($article["link"], "berkeleymews.com/") !== FALSE ) { // SatW // SatW elseif (strpos($article["link"], "www.smbc-comics.com/comic/") !== FALSE) { $imgs = $xpath->query('//img'); //doesn't get simpler than this // only keep everything starting at the first run PCBs as 1 nF. It should be the same form factor, with maybe a little bit of margin // margins from edges h_margin = thickness*2; v_margin = hole_dist_top*2 + thickness; v_margin = hole_dist_top*2 + thickness; width_mm = hp_mm(width); // where to put the output jacks working_height = height - v_margin - title_font_size*2; saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement pwm_in = [first_col, fifth_row, 0]; square_out = [output_column, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, bottom_row, 0]; c_tune = [second_col, second_row, 0]; //Third row interface placement pwm_in = [first_col, fifth_row, 0]; //left_rib_x = thickness * 1; right_rib_x = width_mm - h_margin; working_height = height - v_margin - title_font; saw_out = [h_margin + working_width/4, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; audio_out_2 = [right_col, row_1, 0]; triangle_out = [output_column, row_2, 0]; cv_2b_atten = [right_col, row_1, 0]; triangle_out = [third_col, third_row, 0]; //Fourth row interface placement saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, first_row, 0]; c_tune = [width_mm/2, top_row, 0]; left_rib_x = thickness + 9.5/2 + tolerance*2; // rib + half a jack col_right = width_mm - thickness*2; left_rib_x = hole_dist_side + thickness; col_left = h_margin; bottom_row = v_margin + 12; title_font = 10; // Center two holes hole_r = 1.7; // Hole for setscrew // Make sure bottom ends at z=0 KnobMajorRadius+RingWidth) * 3, 20], center=true); } 3D Printing/Pot_Knobs/print_knob.stl Executable file View File Hardware/PCB/precadsr_Gerbers/precadsr-B_Mask.gbr Normal file Unescape Samba Reggae 1: BSD: .. . . . . . . . . . . .
- Lines Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.
- See Make Noise's Maths, Ken.