PM EDT Precision ADSR with mods Light emitting diode, 5 mm Small Signal NPN Transistor, TO-92 Schottky Barrier Rectifier Diode, DO-41Operational amplifier, DIP-8Operational amplifier, DIP-82 pin Molex connector 2.54 mm spacing"/> Dual Operational Amplifiers, DIP-8/SOIC-8/TSSOP-8/VSSOP-8 Binary files a/3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels/HOLD PORTAL.png' d8deca9307 Delete '3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels/SPIDER CLIMB.png' Delete '3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels' 0 0 Y N 1 F N DEF SW_Push_Dual_x2 SW 0 20 Y N 1 F N DEF SW_SP3T SW 0 0 VCO details from Moritz Klein (https://www.ericasynths.lv/shop/diy-kits-1/edu-diy-vca/ - Two CV inputs for each, allowing you to use your choice of sitching hardware). Consider aesthetics and prcticality of stand-offs from front panel. I adjusted the height of the knob. [mm] sphere_indents_cutdepth = 3; // tweak on this one, but many external clock sources cycle between 0v and 5v or even much less. - One potentiometer for internal clock rate. Switches: One SPST switch to adjust CV output range, switch between 5v and 2.5v max (or whatever is configured). - Momentary-normal-off pushbutton to manually step. - SPST switch per step, to set clock rate // Top left: clock in, speed pot_p160(); // Left side: meta-step controls // step rotary switch with signal lamp, generic K switch SPST right angle, http://spec_sheets.e-switch.com/specs/P040042.pdf E-Switch sub miniature slide switch, EG series, SPDT, https://www.e-switch.com/wp-content/uploads/2022/06/EG.pdf tactile switch, 7.3mm x 6.25mm package, pitch 0.4mm; see section 7.4 of http://www.st.com/resource/en/datasheet/stm32l476me.pdf WLCSP-81, 9x9 raster, 3.639x3.971mm package, pitch 0.4mm; see section 7.4 of http://www.st.com/resource/en/datasheet/stm32l476me.pdf WLCSP-81, 9x9 raster, 4x4mm package, pitch 0.5mm; see section 6.8 of http://www.st.com/resource/en/datasheet/stm32f746zg.pdf TFBGA-265, 17x17 raster, 14x14mm package, pitch 0.4mm; see section 6.8 of http://www.st.com/resource/en/datasheet/stm32f746zg.pdf TFBGA-100, 10x10, 9x9mm package, pitch 0.4mm; see section 7.7 of http://www.st.com/resource/en/datasheet/DM00330506.pdf WLCSP-100, 10x10 raster, 4.201x4.663mm package, pitch 0.4mm; see section 7.5 of http://www.st.com/resource/en/datasheet/stm32f303r8.pdf WLCSP-49, 7x7 raster, 2.999x3.185mm package, pitch 0.5mm; see section 6.3 of http://www.st.com/resource/en/datasheet/stm32f469ni.pdf WLCSP-180, 13x14 raster, 5.537x6.095mm package, pitch 0.5mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f401vc.pdf WLCSP-49, 7x7 raster, 3.277x3.109mm package, pitch 0.4mm; see section 7.6 of http://www.st.com/resource/en/datasheet/stm32l031f6.pdf WLCSP-25, 5x5 raster, 2.423x2.325mm package, pitch 0.4mm; see section 7.8 of http://www.st.com/resource/en/datasheet/DM00387108.pdf Texas Instruments, DSBGA, 0.9x1.9mm, 8 bump 2x4 (perimeter) array.