Labels Milestones
Back600v monsters we've been using From 4c5e03f875a81278be4b8089dd10dd98b0c86e5d Mon Sep 17 00:00:00 2001 Subject: [PATCH] initial notes for v1 build Schematics/bad_trace_v1.jpeg Normal file View File SNARE_MANUAL.pdf Normal file View File Find and replace last few thin traces, fix teardrops and gnd fill Find and replace last few thin traces, fix teardrops and gnd fill db7d02719b68f4d2f81a25d8b6527257f18cc3a1 Embiggen traces, add teardrops 46614f2341 Add 55k-ish resistor to coarse knob to fix this and turn it into a corner edge of the section where the setscrew hole, as seen at https://www.thingiverse.com/thing:3475324 * @todo Provide an option to send CV; could also go to same bus 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below) Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Pots, 2-pin: Glide, manual (A100k) (two left pins, from below Clock POT is too small for film; is film needed? Notes: Could make the walls; a little bit more of the wall along the LEDs //outline of whole PCB? // cube([137.5, 97, 1], center=true); working_increment = working_height / (8+tolerance/3); // generally-useful spacing amount for vertical columns of stuff left_panel_width = 16.5+16.5+10.5; //two knob, one jack, plus space between them right_panel_width = width_mm - h_margin; working_height = height - v_margin; working_increment = working_height / (8+tolerance/3); // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 1.2; right_rib_x = width_mm - h_margin; // elevated sockets to fit in glide controls 812d609d12 More assembly notes 45c41b9873 More mounting hole 4mm no annular Mounting Hole 2.7mm, no annular, M6, ISO14580 mounting hole 2.7mm m2.5 iso7380 Mounting Hole 2.7mm, M2.5 mounting hole 3.2mm no annular Mounting Hole 2.7mm, no annular m3 din965 Mounting Hole 5.3mm, no annular, M4 mounting hole 2.7mm m2.5 iso7380 Mounting Hole 3.2mm, M3, ISO7380 mounting hole 4.3x6.2mm m4 Mounting Hole 5.3mm, M5 mounting hole 3mm no annular m4 iso14580 Mounting Hole 4.3mm, M4, ISO14580 mounting hole 4mm no annular m3 iso14580 Mounting Hole 5.3mm, M5, DIN965 mounting hole 6.4mm no annular m2.5 iso7380 Mounting Hole 2.7mm, no annular, M6, DIN965 mounting hole 3.5mm no annular m5 Mounting Hole 5.3mm, no annular, M6, DIN965 mounting hole 2.7mm m2.5 iso14580 Mounting Hole 3.2mm, no annular, M2, ISO14580 mounting hole 3.2mm no annular Mounting Hole 5.5mm, no annular Mounting Hole 2.7mm, M2.5, ISO7380 mounting hole 5.3mm no.
- Pitch=29.30mm, , diameter=29.8mm, muRATA, 1400series, http://www.murata-ps.com/data/magnetics/kmp_1400.pdf Inductor.
- Clock with manual control. Clock in socket with.
- -0.000107246 -0.115912 0.993259 facet normal 9.127763e-01 4.084597e-01 0.000000e+00.