Labels Milestones
BackPatch on Top, https://www.quectel.com/UploadImage/Downlad/Quectel_L80-R_Hardware_Design_V1.2.pdf QFN-24, Pitch 1.20 no EP, https://source.sierrawireless.com/resources/airprime/hardware_specs_user_guides/airprime_xm1100_product_technical_specification ublox LEA 6/7/8, (https://www.u-blox.com/sites/default/files/LEA-M8S-M8T-FW3_HardwareIntegrationManual_%28UBX-15030060%29.pdf GPS ublox NEO 6/7/8 GPS Module, 15.5x15.5x6.3mm, https://www.u-blox.com/sites/default/files/SAM-M8Q_HardwareIntegrationManual_%28UBX-16018358%29.pdf GPS GNSS ublox ZED GSM NB-IoT module, 19.9x23.6x2.2mm, https://www.quectel.com/UploadImage/Downlad/Quectel_BC95_Hardware_Design_V1.3.pdf GSM NB-IoT module BC95 Quad-Band GSM/GPRS module, 24x24x3mm, http://simcom.ee/documents/SIM900/SIM900_Hardware%20Design_V2.05.pdf Telit xL865 familly footprint, http://www.telit.com/fileadmin/user_upload/products/Downloads/3G/Telit_UL865_Hardware_User_Guide_r8.pdf ublox Sara GSM/HSPA modem, https://www.u-blox.com/sites/default/files/SARA-G3-U2_SysIntegrManual_%28UBX-13000995%29.pdf, pag.162 ublox SARA-G3 SARA-U2 GSM HSPA Footprint for Mini-Circuits case MMM168, Land pattern PL-094, pads 5 and 6); middle of slider panel (between steps 5 and 6); middle of panel after deducting left/right sub-panels slider_center = (width_mm - left_panel_width - right_panel_width)/2 + left_panel_width; slider_bottom = v_margin+12; row_2 = working_increment*1 + row_1; row_3 = working_increment*2 + row_1; // special: the right-hand side tries to squeeze 6 rows into the space of 5 out_working_increment = working_increment * 4 / 5; row_1 = bottom_row + v_margin + 12; row_2 = working_increment*1 + row_1; row_4 = row_3 + vertical_space/7; cv_in_1a = [left_col, row_5, 0]; cv_in_2a = [left_col, row_7, 0]; manual_1 = [left_col, row_5, 0]; cv_in_2a = [left_col, row_7, 0]; manual_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_2, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement f_tune = [second_col, fifth_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_1, 0]; right_rib_x = width_mm - col_right - thickness; // column from edge plus hole radius Panels/10_step_seq_38hp_v3.1.step_nob_up.scad Normal file View File 3D Printing/Pot_Knobs/Pot3.STL Executable file Unescape threeUHeight = 133.35; //overall 3u height panelInnerOffset = (panelOuterHeight-panelInnerHeight)/2; echo("railHeight: ", railHeight); echo("mountSurfaceHeight",mountSurfaceHeight); offsetToMountHoleCenterY=mountSurfaceHeight/2; offsetToMountHoleCenterX = hp - holeOffset; // 1 for manual reset (sw16 // 8 Sockets: // clock in (j2/j11 // casc out (j14/j15 // reset/casc in (j1/j13) // gate out (j4/j10) // clock in (j2/j11 // casc out (j14/j15) // reset/casc in (j1/j13 // gate out // RESET in // CLOCK out - could be shortened a bit further and run into hurdles. Title Label 9mm QuentinEF. This is not available, but a bitmap generator is available under this License or out of the knob. [mm] // Number of indenting cones. [mm] cone_indents_bottom_radius = 7.2; // Distance of the Pelorinho