synth_tools

Back

Length*diameter=20.32*12.07mm^2, Vishay, IHA-101, http://www.vishay.com/docs/34014/iha.pdf Inductor Axial series Axial Horizontal pin pitch 5.00mm length 8mm width 8mm Capacitor C, Rect series, Radial, pin pitch=5.00mm, , length*width=7.2*2.5mm^2, Capacitor, http://www.wima.com/EN/WIMA_FKS_2.pdf C Rect series Radial pin pitch 2.50mm diameter 4.5mm Fastron MECC Inductor, Axial series, Axial, Vertical, pin pitch=7.62mm, , length*diameter=4*2mm^2, , http://www.diodes.com/_files/packages/DO-35.pdf Diode DO-35_SOD27 series Axial Horizontal pin pitch 12.70mm length 35.56mm width 17.78mm Pulse KM-5 L_Toroid, Vertical series, Radial, pin pitch=27.94mm, , diameter=40.64mm, Vishay, IHB-5, http://www.vishay.com/docs/34015/ihb.pdf Inductor Radial series Radial pin pitch 55.88mm 15W length 48mm width 12.5mm height 12.5mm Resistor, Axial_Power series, Box, pin pitch=30.48mm, 4W, length*diameter=18*9mm^2 Resistor Axial_DIN0918 series Axial Vertical pin pitch 27.50mm length 29mm width 7.6mm Capacitor C, Rect series, Radial, pin pitch=7.37mm, 10W, length*width=16.1*9mm^2, http://www.vishay.com/docs/30218/cpcx.pdf Resistor Radial_Power series Radial pin pitch 2.54mm size 5.54x6.5mm^2 drill 1.1mm pad 2.1mm Terminal Block WAGO 236-603 45Degree pitch 10mm size 35x10.3mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00030, 9 pins, pitch 5mm, size 25x8.3mm^2, drill diamater 1.3mm, pad diameter 2.1mm, size source Multi-Contact FLEXI-xV 1.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator ipc_gullwing_generator.py SOIC, 8 Pin (https://www.nxp.com/docs/en/data-sheet/MPL3115A2.pdf#page=42), generated with kicad-footprint-generator Molex SPOX Connector System, 43045-1221 (alternative finishes: 43045-142x), 7 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Inductor SMD 2512 (6332 Metric), 2.6mm thick, Vishay WKS2512, Terminal length (T) 2.21mm, 1 to something more decisive, like 3x. Then a signal as low as 2v could works as an external CV-to-pulse-rate module? Is this even useful? - Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Things best left to external modules: - CV-controlled CV offset module - add a switch to set clock rate (if onboard clock is used) (rv11 // 1 for run/stop (sw14) // 1 for manual glide (rv16 // 1 for 5v / 2.5v output mode // 10 LEDs 3 sockets Subject: [PATCH] Apply jlcpcb's design rules, small fixes for those Fireball/Fireball.kicad_pro | 104 Fireball/Fireball.kicad_sch | 48 dd8c61c34f A couple more minor.

New Pull Request

Labels Milestones